B0040

B0040: Third row left side airbag deployment control circuit fault

DIY difficulty 3/5

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.

Your car's airbag computer found an electrical problem in the wiring that fires the third-row left side airbag. The airbag warning light will stay on, and that side airbag may not deploy in a crash. The car still drives normally.

Key facts

Symptoms

Likely causes

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 6 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Disconnect the battery (negative terminal first) and wait at least 10 minutes before touching any SRS connector or component. Tests: Damaged wiring or a loose/corroded connector in the third row left side airbag circuit…
  2. Read the code with an SRS-capable scan tool and note any subcode digits after the main code (e.g. -11, -12, -13) - many makes append them to say open circuit, short to ground, short to battery, or wires shorted together. Tests: Damaged wiring or a loose/corroded connector in the third row left side airbag circuit…
  3. With power still off, inspect the third-row left seatback side bolster wiring and connectors - slide the seat fully forward and back to expose the under-seat harness and check for pinching, chafing, or corrosion. Tests: Damaged wiring or a loose/corroded connector in the third row left side airbag circuit…
  4. Unplug and inspect the side-airbag connector (usually yellow) for bent pins, moisture, or green corrosion; clean or repair as needed. Tests: Damaged wiring or a loose/corroded connector in the third row left side airbag circuit…
  5. Test the circuit only with the battery disconnected and only per the factory service manual's SRS procedure - never apply power to or probe a live deployment circuit.
  6. Verify the restraints control module's power and ground feeds, repair the fault, reconnect the battery, clear the code, and confirm the airbag light completes its power-on self-test.

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Typical price range

Parts$150 – $600
Labor$150 – $350

Wiring/connector repair under the seat, or side airbag module replacement if the module itself failed. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for B0040 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

3 of 5 — Airbag work demands a battery disconnect plus a waiting period; under-seat harnesses are the usual culprit and are inspected with basic hand tools and a multimeter.

Watch this repair on YouTube

Parts & tools

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →