Community-sourced DIY repair guides for the 2009–2018 Ram 1500, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Owner-verified repair guides
Hemi tick: exhaust manifold vs lifter diagnosis Owner-verified(5.7L HEMI V8)
No teardown needed for diagnosis — reach the exhaust manifold heat shields through the front wheel wells with the engine cold, and use a mechanic's stethoscope or long screwdriver against the block versus the manifold to isolate the sound.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Torque specs
Exhaust manifold bolts/studs: verify — Broken-bolt extraction is the job here — confirm torque and sequence against factory service info before reinstalling. Aftermarket upgraded bolts are the community preference over the factory ones that keep breaking.
Tips
Learn the two ticks before spending a dollar: an exhaust-manifold tick is sharp, usually one-sided, and FADES as the engine warms (heat expansion seals the leak). A lifter tick is rhythmic with RPM, persists or worsens HOT, and is the serious one — a collapsed MDS lifter eats the cam lobe.
Free first test with a cold engine: reach through the wheel wells and grab the corners of the manifold heat shields. A loose/rattling shield means broken bolts underneath — owners report it is almost always the rearmost bolt(s), 9 times out of 10 on the driver's side.
Stethoscope split: probe the engine block and then the manifold. Lifter tap transmits through the block; an exhaust leak is loudest at the manifold flange and the first two studs. One owner isolated his tick to the front manifold studs this way after a shop had already 'fixed' the gasket.
Don't confuse it with injector noise: with the hood closed and the engine hot, a healthy Hemi is nearly silent. Faint high-pitched ticking with the hood open is normal injectors; a pronounced tick you can hear from another truck driving by is not.
If the tick never fades AND you have a misfire code (P0300/P0302), stop driving it gently and plan for lifters and cam — roughly $2,000-2,500 at an independent shop. One owner was quoted $10k for a whole engine by a shop that skipped the diagnosis; the cam/lifter job fixed it.
Prevention consensus is boring but real: 5W-20 full synthetic on a short interval. Multiple owners tie neglected oil to lifter failures, and a fresh oil change washing sludge out can unmask a tick that was already there.
All four leak points are reachable without major teardown: the 3rd brake light and shark fin from outside, the cab vents behind the rear seat (seat removal), and the rear window frame from outside with the trim pulled.
Torque specs
3rd brake light screws / vent fasteners: verify — No torque-critical fasteners here — snug by hand. Overtightening the brake light screws warps the housing and recreates the leak.
Tips
Map the symptom to the source before sealing anything: wet headliner at the rear corners points at the 3rd brake light; damp carpet under the rear seat with a dry headliner points at the cab pressure vents; water sloshing sounds mean it has been leaking a while — check everywhere.
The 3rd brake light gasket is the #1 culprit across a half-dozen threads. Replace the stick-on weatherstripping (about $10-15) rather than caulking over the old sponge — owners who just siliconed over it often leaked again. Snug the screws by hand; overtightening warps the housing.
The cab vents (exhausters) behind the rear seat are the #2 culprit and the one everyone misses. Pull the rear seat, replace both vent assemblies (Mopar 68323649AB, roughly $8 a side) — several owners fixed years of leaks only after doing the vents alongside the brake light.
While you are back there, check the shark-fin antenna base — owners report it works loose, and a bead of silicone around it plus a snug-down has ended leaks. Then run a bead of flowable silicone along the top and sides of the rear window frame; the factory glass sealant dries out and gaps, especially at the corners.
Assume two leaks, not one. Multiple owners documented fixing the brake light only to find the vents or window still leaking — one owner with a 2019 found the brake light AND both sides of the rear window leaking independently. Water-test with a hose after each fix before reassembling the interior.
Dry it like you mean it: pull the rear seat and carpet, towel out standing water, and leave a dehumidifier in the cab overnight. One owner ran the truck's heater as a dehumidifier and regretted the gas bill — a plug-in dehumidifier is cheaper.
Work through the front wheel wells with the truck on jack stands, wheels off, and the engine stone cold. The manifold heat shields come off first; every bolt you touch gets a PB-Blaster soak before you touch it.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Torque specs
Exhaust manifold bolts (to head): 18 ft-lb (owner-reported; verify) — Owner-reported figure; verify against factory service info. Center-out widening circle sequence. Re-check after one full heat cycle.
Exhaust manifold heat shield bolts: verify — Shield corners get grabbed for the broken-bolt diagnosis; replace cracked shields while in there.
Tips
Confirm it's bolts before you wrench: the rearmost bolt(s) break first, 9 times out of 10 on the driver's side. Grab the heat shield corners through the wheel well with the engine cold - a loose/rattling shield means broken bolts underneath. The companion diagnosis note (hemi-tick-diagnosis) walks the exhaust-tick-vs-lifter-tick split.
Extraction is the whole job. If the stud snapped above flush, Vise-Grips may walk it out. If it's flush or below, welding a nut onto the stub is the community's go-to - one owner needed ~15 tries to get the nut to stick, then worked it out gingerly. Easy-outs and re-tapping are the last resorts, not the first.
Don't bolt a warped manifold back on. These cast-iron manifolds heat-cycle out of plane, and bolting them flat is what snaps the next set of bolts. Owners machine-shop the manifolds or flatten them themselves with a belt sander (120 grit works) until every port shows even contact.
Remflex gaskets plus quality hardware is the owner's preferred combo over stock bolts, which owners report just break again. One owner pair: 'milled OEM manifolds + Remflex + ARP' - skip the cheap shorty headers; long tubes or flattened stockers are the respected options.
Reassemble to ~18 ft-lb starting from the center bolts and working outward in a widening circle, then do a full heat cycle and re-check torque - multiple owners found bolts had loosened after the first heat cycle. The driver's side is the hard one (steering column and dipstick in the way); remove the heat shield and manifold together out the back.
Verify the torque figure and bolt sequence against factory service info before reinstalling - the 18 ft-lb figure is owner-reported, and rearmost bolts on later trucks use updated stainless hardware that must go back in the same positions.
Full diagnosis (coil/plug/injector swap, compression test) is all under-hood, no teardown. The repair itself is heads-off engine work: intake off, heads pulled, cam out the front. Plan a full weekend and a parts list before you start.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Torque specs
Rocker arm / valvetrain hardware: verify — Heads-off cam/lifter job - torque every valvetrain fastener and the cam bolt per factory service info; owner parts lists don't publish torque specs.
Tips
The signature start is a single-cylinder misfire (often P0305) that a tick which never fades joins. The 2011 thread's owner: cylinder 5 misfire, ruled out plugs/coil/injector/wiring, compression 200 psi on the bad cylinder (5% of a healthy neighbor - so it CAN'T be top-end sealing), which left the cam/lifter as the only suspect. That's the diagnostic chain to copy.
Rule out the cheap stuff first: swap coil and plug to another cylinder and see if the misfire moves. If the misfire stays on the same cylinder with good compression, you're likely looking at a collapsed MDS lifter eating the cam lobe - owners find the lobe visibly worn (cylinders 2, 5, 8 reported) once the cam comes out.
While you're in there, budget the full job like the owners do: cam, all lifters, all 4 MDS solenoids, VVT solenoid, timing chain + VVT phaser, oil pump (Melling high-volume is the community favorite), water pump, plugs, coils, and check the heads. One owner landed at ~$3,500 in genuine parts for the whole job and another at ~$1,800 doing the top end himself over a couple of weekends.
MDS lifters are the usual victim, but owners report non-MDS Hemis failing the same way - the community's blame list is poor lifter needle-bearing quality plus lubrication failure from extended idling, not just the MDS design. Don't let a non-MDS truck talk you out of checking.
The owner consensus on prevention: 5,000-mile oil changes, quality oil and filter, and don't let the truck sit idling for long stretches. It doesn't hit every truck - but it's common enough on the 4th gen that a 2011 owner planned his whole rebuild budget around it.
Verify part numbers and torque specs against factory service info before ordering - Mopar front lifters have gone through supersessions and owners report availability quirks. Replace the MDS solenoids while the lifters are out; they're cheap insurance on a teardown this deep.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
NHTSA recorded 1,544 complaints for the 2009–2018 Ram 1500. 2016 was the worst year (1544 complaints). Most-reported areas: steering, engine, service brakes.
18V486000 (27/07/2018) — STRUCTURE:BODY:TAILGATE Chrysler (FCA US LLC) is recalling certain 2015-2017 RAM 1500, 2500, and 3500 pickup trucks equipped with a power locking tailgate and either a 5 foot, 7 inch or 6 foot, 4 inch bed. The tailgate actuator limiter tab may…
19V757000 (24/10/2019) — ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE) Chrysler (FCA US LLC) is recalling certain 2014-2019 Ram 1500 and 1500 Classic Pickup trucks equipped with 3.0L Eco Diesel engines. The Exhaust Gas Recirculation (EGR) cooler may crack and allow pre-heated vaporized coolant to enter the EGR system. This…
17V198000 (23/03/2017) — POWER TRAIN:DRIVELINE:DIFFERENTIAL UNIT Chrysler (FCA US LLC) is recalling certain 2016-2017 Ram 1500 trucks. The differential pin retaining screw may come loose while driving, potentially causing the differential to break or lock up.
16V167000 (23/03/2016) — STEERING:ELECTRIC POWER ASSIST SYSTEM Chrysler (FCA US LLC) is recalling certain model year 2015-2016 Ram 1500 trucks manufactured January 22, 2015, to September 13, 2015. Contamination on the Electric Power Steering (EPS) control circuit board may cause a short and result in the loss…
17V821000 (20/12/2017) — POWER TRAIN:AUTOMATIC TRANSMISSION:LEVER AND LINKAGE:COLUMN SHIFT Chrysler (FCA US LLC) is recalling certain 2016-2017 Ram 3500 Cab Chassis with a Gross Vehicle Weight Rating (GVWR) of less than 10,000 lbs, 2011-2017 Ram 3500, 4500 and 5500 Cab Chassis vehicles, 2009-2017 Ram 1500 and 2010-2017 Ram 2500…
18V332000 (17/05/2018) — ELECTRICAL SYSTEM:WIRING Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500…
17 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
We don't have factory bulletin data for the 2009–2018 Ram 1500 yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.