Community-sourced DIY repair guides for the 2003–2008 Infiniti G35, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Owner-verified repair guides
VQ35DE oil consumption: piston rings, the RevUp, and the factory oil-consumption TSB Owner-verified(3.5L VQ35DE V6)
Check the dipstick every fill-up. If burning a quart per 1,000-2,000 miles with no external leaks, a dealer oil-consumption test (requires documented service history) is the formal path - otherwise manage by topping off.
Typical difficulty: Moderate — based on 5 code guides for the oil repair area (an area-level estimate, not this exact job).
Torque specs
Oil pan drain plug: verify — Do not guess this value - look it up in the G35 FSM (EM section for engine items, BR for brakes, CL for clutch) and use a torque wrench.
Tips
The VQ35DE has a long owner-documented history of oil consumption dating back to 2002. It is worst on the RevUp 6MT cars (2005-2006): starting in 2005 Nissan used a lighter oil-scraper-ring expander, and owners report the ring skipping over the bore once carbon builds up, burning roughly 1 quart per 1,000-2,000 miles.
There is an Infiniti oil-consumption TSB covering 2005 through May 29, 2007 (CV35) M/T cars per owners - but a TSB is documentation, not a recall or warranty. Without service records and an active powertrain warranty, dealers denied the replacement, per multiple owners.
One owner reported being quoted $3,000+ for piston ring replacement; another was quoted roughly $2,000 in labor alone. A built short block ran $3,000+ in parts per owners, for $5,000-6,000 installed - expensive enough that most owners just top off instead.
Keep the oil topped off: running these engines low on oil is how owners turn consumption into a spun bearing. Check the dipstick every fuel stop, not every oil change.
Several owners note their cars drink synthetic faster than conventional - if consumption is heavy, cheaper conventional oil topped off often is the pragmatic move; expensive oil does not fix worn rings.
Before condemning the rings, rule out the PCV system and the valve-cover spark plug tube seals - both are common G35 oil-loss paths that are far cheaper than a ring job.
Power windows: failing motors, frayed regulator cables, and the limit-switch reset Owner-verified(3.5L VQ35DE V6, 3.5L VQ35HR V6)
Door panel removal (a few screws plus push pins). The motor is mounted to the regulator inside the door; run the switch until the motor mounting screws are visible to detach it.
Torque specs
Door panel screws and window regulator fasteners: verify — Do not guess this value - look it up in the G35 FSM (EM section for engine items, BR for brakes, CL for clutch) and use a torque wrench.
Tips
The classic G35 window failure is the window rolling all the way up then immediately dropping back down several inches. That is not always a dead motor - the limit switch lost its reference and needs a reset after glass work or battery disconnects.
Per the FSM procedure owners posted: remove the motor from the regulator, run it 5+ seconds in the up position with the switch, reassemble, then set the limits with MANUAL up and MANUAL down only - never use the auto functions for the reset steps. Sedan rear windows have no reset button; the procedure differs from the fronts.
If the motor is genuinely dead (clicks but does not move), cleaning the carbon and debris out of the motor and regreasing often brings it back - one owner fixed his for years that way. The brushes wear too; owners report replacing them with hobby-store brushes (light sanding to fit, a bit of soldering) for about $5 instead of a new motor.
While the door panel is off, inspect the regulator cables for fraying - frayed cables jam the mechanism and mimic a motor failure.
Emergency trick owners confirm: banging the bottom of the door panel with a fist can wake a dead motor once or twice to get the window up.
Cam/crank position sensors: P0340/P0345/P0335, stalling, and long cranks Owner-verified(3.5L VQ35DE V6, 3.5L VQ35HR V6)
Bank 1 cam sensor: passenger side, rear of the cylinder head. Bank 2 cam sensor: driver's side, under the throttle body area. Crank sensor: rear of the engine near the transmission bellhousing.
Typical difficulty: Moderate — based on 841 code guides for the sensors repair area (an area-level estimate, not this exact job).
Torque specs
Camshaft/crankshaft position sensor mounting bolt: verify — Do not guess this value - look it up in the G35 FSM (EM section for engine items, BR for brakes, CL for clutch) and use a torque wrench.
Tips
Failing cam or crank sensors cause stalling, long cranks, and hard starts - sometimes with no codes at all. The VQ35DE has one cam sensor per bank (P0340 = bank 1, P0345 = bank 2); on these cars bank 2 is the DRIVER'S side, which is backwards from most makes and trips up owners.
Use OEM (Nissan/Infiniti) sensors. One 2008 G35 owner replaced the crank sensor with an aftermarket part, saw the stalling return in about a week, then fixed it - briefly - with a genuine OEM sensor. Budget aftermarket sensors have a poor reputation on this job.
If codes persist after sensor replacement, suspect the wiring: inspect connectors, reference voltage, and harness continuity to the PCM before throwing more parts. The 2008 owner's stalling returned even after OEM sensors, pointing at heat-related wiring/harness issues.
The 2007-2008 VQ35HR sedans have FOUR cam sensors (intake and exhaust per bank) due to dual VVT - confirm which engine you have before buying.
Door lock actuators: fob and switch make noise but the locks do not move Owner-verified(3.5L VQ35DE V6, 3.5L VQ35HR V6)
Door panel removal (3 screws plus push pins). The actuator lives deep inside the door behind the window regulator area; the $5 DIY mounts the universal actuator to the door panel itself.
Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).
Torque specs
Door panel and actuator mounting hardware: verify — Do not guess this value - look it up in the G35 FSM (EM section for engine items, BR for brakes, CL for clutch) and use a torque wrench.
Tips
The classic failure: you press the fob, hear a whirring gear sound from inside the door, the horn and lights respond, but the lock latch barely twitches. The door lock actuator motor is dying - a common G35 failure across 2003-2007.
Symptoms can be worse in hot weather - several owners report locks failing only when it is hot out, then working again when cool.
The forum-famous fix is a $5 universal door lock actuator mounted to a homemade aluminum bracket inside the door panel, bypassing the failed OEM motor. Owners document the full procedure including the 03-04 vs 05-07 door-panel differences.
Dealer route: one owner was quoted $150 for the part plus $250 labor per door. An independent shop is cheaper than the dealer for this job.
Before condemning the actuator, check that the metal lock cable inside the door has not simply popped out of its retainer - one owner fixed his 'failed actuator' by reseating the cable.
Bose audio: sound cuts out or distorts - diagnose the amp vs the headunit before buying parts Owner-verified(3.5L VQ35DE V6, 3.5L VQ35HR V6)
The Bose amp is in the trunk. The headunit pulls from the center dash - remove it to check connections before condemning the amp.
Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).
Torque specs
Amp and headunit mounting hardware: verify — Do not guess this value - look it up in the G35 FSM (EM section for engine items, BR for brakes, CL for clutch) and use a torque wrench.
Tips
The failure pattern: the stereo plays fine at startup, then sound cuts out entirely after 30 seconds to a minute, and sometimes comes back heavily distorted. It worsens over months until the radio is silent most of the time.
Do not assume the amp is dead - one owner chased the amp, then discovered his NAV voice prompts still played, which proved the amp was fine and the headunit was the problem. If NAV voice still speaks through the speakers, the amp works and the fault is upstream.
On the 03-04 Bose cars the headunit has no internal amp and sends a differential-balanced signal to a trunk-mounted amp. Replacement amps must accept balanced/differential inputs (owners used JL amps with high-level inputs); one owner measured the headunit output at 2.2V peak-to-peak - no line-output converter needed for that level.
Keep the shielded twisted-pair wiring intact when tapping the signal - pinching the shield is what causes the alternator-whine noise owners report after amp swaps.
Senders are accessed under the rear seat through the tank access covers. Work fuel-safe: disconnect the battery, relieve fuel pressure, and ventilate.
Typical difficulty: Moderate — based on 483 code guides for the fuel repair area (an area-level estimate, not this exact job).
Torque specs
Fuel tank access cover fasteners: verify — Do not guess this value - look it up in the G35 FSM (EM section for engine items, BR for brakes, CL for clutch) and use a torque wrench.
Tips
The G35 has TWO fuel level senders (fuel pump side + driver/sub side). A gauge that reads past-full at fill-up and never drops below half is the classic sender failure pattern - but so is a failed combination meter, so diagnose before buying parts.
Measure first: the pump-side sender should sweep roughly 3-80 ohms (pins 2 and 5 on the pump harness) from full to empty, the sub side roughly 3-43 ohms. If resistance sweeps correctly, the senders are good and the fault is the cluster.
The documented root cause on many senders is the brass dome contact on the float arm wearing flat and bridging multiple resistor-board traces. Owners have fixed it by cleaning the board and re-rounding the dome with an emery board.
Several owners replaced both sending units AND the fuel pump and still had the problem - the fault was the instrument cluster (cold solder joints on the resistor network). Reflowing the cluster solder joints fixed gauges that could not read empty.
Use the cluster self-test first: hold the trip reset button, turn the ignition on, then push the trip button 10 times in about 5 seconds. Needles drop to reference positions - if the fuel needle sticks, the cluster is the problem.
The tank-sealing O-rings (blue) expand on contact with gasoline - keep them dry during the job and replace them whenever the tank is opened, per the FSM.
Valve covers: oil in the spark plug wells - the integral tube-seal trap Owner-verified(3.5L VQ35DE V6)
Upper and lower intake plenum removal is required to reach the covers (FSM EM section). Covers lift off after coils, PCV hoses, and harness brackets are clear.
Torque specs
Valve cover bolts: verify — Do not guess this value - look it up in the G35 FSM (EM section for engine items, BR for brakes, CL for clutch) and use a torque wrench.
Tips
On the VQ35DE the spark plug tube seals are molded into the valve cover - there is no separate service part. A plain valve-cover gasket set will NOT fix oil pooling in the spark plug wells; if the wells are oily you need new valve covers (or the workaround below).
Oil in the plug wells shorts the coil boot and causes cylinder misfires (P0304/P0300) that stay with the cylinder even after swapping coil packs - if the misfire does not follow the coil, check the wells.
The owner-documented workaround: remove the covers, drill out the old tube seals with a 1-7/8 inch hole saw, and press in replacement seals - one owner reported 10,000 miles leak-free afterward for about $100 in parts for both sides versus several hundred per new valve cover.
Check the wells at every spark plug change - oil in the tubes is common and many owners find it before any misfire. The FSM procedure does not require draining the coolant despite what some manuals imply (confirmed by Z1 Motorsports against the FSM).
Note the difference from the oil-consumption note: oil in the plug wells fouls the outside of the plug and coil boot, while worn piston rings foul the electrode inside the combustion chamber.
P0507 high idle after throttle-body cleaning or battery disconnect: the idle air volume relearn Owner-verified(3.5L VQ35DE V6, 3.5L VQ35HR V6)
No disassembly - the procedure is done from the driver's seat with a stopwatch. A scan tool helps confirm the 650 rpm target and clear the code afterward.
Typical difficulty: Moderate — based on 307 code guides for the intake repair area (an area-level estimate, not this exact job).
Torque specs
Throttle body mounting bolts: verify — Do not guess this value - look it up in the G35 FSM (EM section for engine items, BR for brakes, CL for clutch) and use a torque wrench.
Tips
P0507 (idle speed higher than expected) is the classic consequence of cleaning the electronic throttle body without disconnecting the battery and unplugging the throttle body first. The ECM's learned idle-air volume no longer matches the cleaned throttle plate.
The FSM 'pedal dance' (posted verbatim by owners): accelerator released position learn, throttle closed position learn, then with a fully warm engine - ignition OFF 10+ sec, ignition ON 3 sec, pump the pedal fully 5 times within 5 seconds, wait 7 seconds, hold the pedal down ~20 seconds until the MIL stops blinking and stays on, release within 3 seconds, start and idle.
Preconditions are strict and the learn cancels if any is missed even for a moment: battery voltage above 12.9V at idle, coolant 70-100 C, all electrical loads OFF, wheels straight, vehicle stopped, transmission warmed up. Low battery voltage is a common silent cause of failure.
It is finicky - one owner needed about 50 attempts. Target idle is roughly 650 +/- 50 rpm. When the idle drops into the correct zone, owners report you must turn the car off and immediately back on to make it stick.
If the relearn completes (CMPLT) but idle is still high, look for intake leaks downstream of the throttle body or a faulty PCV valve per the FSM diagnostic path.
Front brakes: fast pad wear and judder on 2003-2005 cars Owner-verified(3.5L VQ35DE V6, 3.5L VQ35HR V6)
Front pads and rotors are a straightforward driveway job: wheels off, caliper bracket bolts, compress the piston. Bed the new pads per the manufacturer's procedure.
Typical difficulty: Moderate — based on 265 code guides for the brake repair area (an area-level estimate, not this exact job).
Torque specs
Caliper bracket bolts: verify — Do not guess this value - look it up in the G35 FSM (EM section for engine items, BR for brakes, CL for clutch) and use a torque wrench.
Tips
The early V35 brakes stop hard but eat themselves: owners report front pads gone in as little as 12,000 miles and rotors juddering soon after. Infiniti upsized the brakes mid-generation (dual-piston front calipers and larger rotors on 2005-2007) - which tells you the originals were marginal.
The judder most owners call 'warped rotors' is usually uneven pad-material deposits on the rotor face, not a bent rotor - which is why fresh rotors can judder again within months if the bedding and pad choice do not change.
Owners who switched to ceramic pads (Akebono is the forum favorite) report much less dust, less noise, and roughly double the pad life, with braking performance still better than average.
Dealer brake parts carry a 12-month/12,000-mile warranty per owners; owners universally advise going aftermarket on price for pads and rotors.
When doing pads, do not spray water on hot rotors to clean brake dust - thermal shock cracks them.
6MT sticky clutch pedal: the lock nut, the clutch line, and the master cylinder Owner-verified(3.5L VQ35DE V6)
Pedal-box access from the driver's footwell for the adjustment; the slave cylinder and clutch line are under the car along the transmission.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Torque specs
Clutch line fittings and master cylinder mounting nuts: verify — Do not guess this value - look it up in the G35 FSM (EM section for engine items, BR for brakes, CL for clutch) and use a torque wrench.
Tips
The 6MT sticky-pedal syndrome: the clutch pedal gradually stops returning to the top as you drive, sometimes sinking so far the car cannot be shifted. It often gets worse as the day warms up.
Check the simple causes first: clutch fluid level and leaks along the clutch line (owners found tiny leaks at the heat-shield-wrapped line that let air in long before dripping). A full flush and bleed is the first step.
The fix that surprises owners: the lock nut behind the clutch pedal adjustment rod wiggles loose, letting the rod rotate and drop the pedal. Re-adjust the rod, tighten the nut, and add blue Loctite - one owner ended his chronic sticky pedal this way after months of bleeding.
Failing clutch master cylinders are also common - several owners fixed the same symptom with a master cylinder replacement. If you replace one hydraulic part, owners strongly recommend doing the master and slave together with fresh fluid.
Video-documented shortcut: loosen the lock nut behind the pedal fork and turn the master-cylinder pushrod 2-4 turns to raise the pedal - no fork or pin removal needed.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
DIY-friendliness scorecard
Score: 101/100 — DIY-friendly
Special tools mentioned in the notes (1, −4): scan tool with live data.
Documented dealer-only steps (0, −0): none documented in the notes — that does not mean none exist.
How this is scored (mechanical, no opinion): start at 100; −4 per distinct special tool mentioned in the notes (max −28); −15 per documented dealer-only step (max −30); note-volume band: 15+ notes +10, 8–14 +5, 4–7 +0. Bands: 85+ DIY-friendly · 65–84 DIY with care · 40–64 Experienced DIY only · below 40 Think twice. Pilot rubric — flagged for Robbie’s eyeball before any scale-up.
NHTSA recorded 339 complaints for the 2003–2008 Infiniti G35. 2004 was the worst year (244 complaints). Most-reported areas: air bags, engine, electrical system.
06E060000 (29/06/2006) — EXTERIOR LIGHTING CERTAIN AAI MOTORSPORTS COMBINATION LAMPS SOLD AS REPLACEMENT LAMPS FOR USE ON THE ABOVE LIST PASSENGER VEHICLES. COMBINATION LAMPS NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS…
11E024000 (24/06/2011) — POWER TRAIN:CLUTCH ASSEMBLY ZF SERVICE IS RECALL CERTAIN CLUTCH KIT ASSEMBLIES, PART NUMBER SX: K70358-01, SHIPPED TO WHOLESALERS AS SERVICE PARTS BETWEEN SEPTEMBER 1, 2010, AND MARCH 8, 2011. THESE SERVICE PARTS ARE INTENDED FOR USE ON MODEL YEAR 2003-2006 NISSAN 350Z AND…
05V555000 (13/12/2005) — FUEL SYSTEM, GASOLINE ON CERTAIN PASSENGER AND SPORT UTILITY VEHICLES, THE FUEL FILLER HOSE MAY CRACK AND RESULT IN FUEL LEAKAGE FROM THE HOSE WHILE REFUELING.
08V521000 (07/10/2008) — AIR BAGS NISSAN IS RECALLING 204,361 MY 2007-2008 ALTIMA, ALTIMA HYBRID, 350Z, 350Z ROADSTER, MY 2008 ALTIMA COUPE, ROGUE, MY 2009 MURANO, AND INFINITI MY 2007-2008 G35 SEDAN, MY 2008 G37 COUPE AND EX35 PASSENGER VEHICLES EQUIPPED WITH CONTINENTAL AUTOMOTIVE SYSTEMS' OCCUPANT…
4 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
We don't have factory bulletin data for the 2003–2008 Infiniti G35 yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.