Community-sourced DIY repair guides for the 2014–2019 Chevrolet Silverado 1500, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
The 5.3L EcoTec3 L83 uses coil-near-plug with short plug wires, so plugs are reached from the top of the engine with no major component removal — pull the plug wires off with plug-wire pliers and the coils/wires lift out. The #8 plug (passenger side, against the firewall) is the known nightmare: it is nearly unreachable from above, and the fix owners use is jacking the front passenger side, removing the wheel and fender liner, and going through the wheel well.
Typical difficulty: Easy — based on 64 code guides for the ignition repair area (an area-level estimate, not this exact job).
Sources: owner forum / guide · owner forum / guide · owner forum / guide · owner forum / guide
P0300 on this Chevrolet Silverado 1500 — full diagnosis guide →
No owner reports yet — fixed this yourself? tell us how
Bank 1 is the driver's side, Bank 2 the passenger side; Sensor 1 sits in the exhaust manifold before the catalytic converter, Sensor 2 after the cat. All four are reached from underneath the truck on jack stands — the connectors are the tight part, routed up along the body, so trace the old sensor's harness path before pulling it.
Typical difficulty: Moderate — based on 841 code guides for the sensors repair area (an area-level estimate, not this exact job).
Sources: owner forum / guide · owner forum / guide · owner forum / guide · owner forum / guide
P0135 on this Chevrolet Silverado 1500 — full diagnosis guide →
No owner reports yet — fixed this yourself? tell us how
The thermostat housing sits at the front of the engine at the engine-side end of the upper radiator hose. Drain the coolant first, then unbolt the housing with a 10mm socket; if the truck still has the stock air intake it may need to come off for clearance. Owners note the thermostat comes integrated with the housing as the GM water-pump outlet assembly (GM PN 15-11125), not a separate drop-in thermostat.
Typical difficulty: Moderate — based on 294 code guides for the cooling repair area (an area-level estimate, not this exact job).
Sources: owner forum / guide · owner forum / guide · owner forum / guide · owner forum / guide
P0128 on this Chevrolet Silverado 1500 — full diagnosis guide →
No owner reports yet — fixed this yourself? tell us how
Front-only job done wheel-off from the front of the truck. Remove the caliper guide-pin bolts and hang the caliper off the brake line; then remove the two large bracket-to-knuckle bolts (18mm bracket bolts per 1A Auto/TRQ walkthroughs). The rotor is held to the hub by a single T30 Torx retainer screw — remove it before pulling the rotor. Rotors commonly rust-seize to the hub on these trucks; tap around the rotor hat with a rubber mallet (or threaded jack bolts in the rotor puller holes where equipped) to break the rust bond. Clean the slide pins and re-lube with silicone brake grease; pump the pedal several times before driving.
Typical difficulty: Moderate — based on 265 code guides for the brake repair area (an area-level estimate, not this exact job).
Sources: tahoeyukonforum — caliper bracket torque thread (129 ft-lb front for 1500, 221 for 2500) · 2017 Silverado brake caliper torque specs guide (bracket 175 Nm/129 ft-lb front, 15 series) · 2016 GMC Sierra brake caliper torque specs guide (guide pins 100 Nm/74 ft-lb) · chevy-specs.com — 2018 Silverado 1500 5.3L brake torque specs (slide bolts 74 ft-lb) · gm-trucks.com — GM truck lug nut torque guide (K2XX 140 lb-ft, 22mm, star pattern) · chevroletforum.com — is the single T30 Torx rotor screw necessary? (Silverado owners) · bobistheoilguy forum — seized rotor to hub, clean hub face + anti-seize · TRQ/1A Auto — How to Replace Front Brakes 2014-2018 Chevrolet Silverado 1500 (tools, steps) · Motor Trend — Power Stop pad bedding procedure
C0035 on this Chevrolet Silverado 1500 — full diagnosis guide →
No owner reports yet — fixed this yourself? tell us how
Battery is a Group 48 (H6) top-post unit in the engine bay on the passenger side. Access per the CarParts 2014-2019 walkthrough: remove the reinforcing/fender brace bar that crosses over the battery, disconnect the terminals (10mm), remove the battery hold-down clamp, then move the coolant reservoir aside to lift the battery out. Tools per 1A Auto's 2014-2019 Silverado video: 10mm and 13mm sockets plus ratchet/extensions.
Typical difficulty: Involved — based on 854 code guides for the battery repair area (an area-level estimate, not this exact job).
Sources: CarParts.com — How to replace the Battery 2014-2019 Chevrolet Silverado (chapters: reinforcing bar, clamp, coolant reservoir aside) · 1A Auto — How to Replace Battery 14-19 Chevy Silverado (10mm/13mm tools, applies 2014-2019) · Landshark Garage — Group 48 top-post battery swap, 2008-2020 Silverado/Sierra pickups · carcarekiosk — Chevrolet Silverado battery replacement notes (presets, transmission relearn behavior)
P0560 on this Chevrolet Silverado 1500 — full diagnosis guide →
No owner reports yet — fixed this yourself? tell us how
Top-side access from the engine bay on the 5.3L — the alternator sits high on the driver side; no wheel-well work needed (owner-reported 45-minute job on 2014-2020 trucks). Steps per CarParts' 2014-2019 Silverado 5.3L video: disconnect the negative battery cable first; rotate the serpentine-belt tensioner with a breaker bar and slip the belt off the alternator pulley (photo the belt routing before removal); remove the output-wire nut and unplug the electrical connector; remove the mounting bolts (15mm) and lift the alternator out. Note: the aluminum mounting bracket has sliding spacers that can bind — back them off gently rather than forcing the alternator (owner video).
Typical difficulty: Involved — based on 854 code guides for the battery repair area (an area-level estimate, not this exact job).
Sources: CarParts.com — How to replace the Alternator 2014-2019 Chevrolet Silverado 5.3L (37 ft-lb / 11 ft-lb torques, belt-off procedure, disconnect battery) · Owner walkthrough — 2014-2020 GMC Sierra/Silverado alternator replacement (45-min top-side job, sliding-spacer tip) · truckmodcentral — Silverado/Sierra alternator how-to (belt routing, 37 ft-lb mounting bolts, voltage verification)
P0620 on this Chevrolet Silverado 1500 — full diagnosis guide →
No owner reports yet — fixed this yourself? tell us how
There is no factory access panel on K2XX Silverados, so owners either unbolt and lift or shift the bed aside, or drop the tank with a floor jack (the 2015 5.3L walkthrough drops the tank using ramps, jack stands, and 10/13/15/8mm sockets). Either way, disconnect the battery, relieve fuel pressure, and disconnect the filler neck, EVAP lines, and the pump's electrical connector before lowering anything. The in-tank module is spring-loaded and held by a locking ring, turned with a brass punch and hammer or a lock-ring tool; on 2014+ trucks the pressure regulator is built into the pump module itself. New modules come with a fresh tank gasket, and silveradosierra owners recommend replacing the locking ring at the same time.
Typical difficulty: Moderate — based on 483 code guides for the fuel repair area (an area-level estimate, not this exact job).
Typical time: “Budget 2-3 hours and basic hand tools; the 2017 Silverado walkthrough rates this an intermediate-difficulty job.” — as written in the note. First-timers often take twice this.
Sources: 1A Auto: How to Replace Fuel Pump Assembly 2014-2018 Chevrolet Silverado 1500 (2015 5.3L walkthrough) · 2017 Chevy Silverado fuel pump replacement DIY walkthrough · silveradosierra.com: Fuel Pump Failing? (bed lift vs tank drop, locking ring, Haynes pressure specs)
P0087 on this Chevrolet Silverado 1500 — full diagnosis guide →
No owner reports yet — fixed this yourself? tell us how
On the L83 5.3L the electronic throttle body bolts to the front of the intake manifold: pull the air intake tube (loosen its clamps), unplug the TB electrical connector, and remove the four bolts to lift it off. Clean the bore and blade with throttle-body cleaner only, moving the blade slowly and only as far as needed; owners warn not to overtighten the small bolts on reinstall. Disconnecting the battery resets the ECM's learned idle airflow, so expect a high or hunting idle afterward. Run the no-scan-tool relearn: idle in Park 3 minutes, ignition off 60 seconds, idle in Park another 3 minutes; if idle is still off, drive above 45 mph with several decelerations, then idle 5 minutes.
Typical difficulty: Moderate — based on 307 code guides for the intake repair area (an area-level estimate, not this exact job).
Typical time: “Run the no-scan-tool relearn: idle in Park 3 minutes, ignition off 60 seconds, idle in Park another 3 minutes; if idle is still off, drive above 45 mph with several decelerations, then idle 5 minutes.” — as written in the note. First-timers often take twice this.
Sources: silveradosierra.com: Throttle body cleaning/maf thread · YouTube: How to reset high/low idle on Chevrolet Tahoe, Silverado after throttle body replacement or cleaning · aFe 87mm throttle body install manual (2014-2023 Silverado 1500 5.3L), factory spec 10 N·m / 89 in-lb
P0121 on this Chevrolet Silverado 1500 — full diagnosis guide →
No owner reports yet — fixed this yourself? tell us how
The 6L80 behind the 5.3L has no dipstick: level is set through the check plug at the rear of the pan, which sits over an internal standpipe that defines the fluid height, and fluid is added through the case fill plug with a hand pump. A 2015-truck walkthrough shows the 18-bolt pan dropping without moving any exhaust components; swap the filter and its rubber neck seal (the seal is the fiddly part), clean the pan and magnet, and reinstall with a new gasket. Refill with Dexron VI, then set the final level with the engine running and fluid temperature at 86-122°F (30-50°C): pull the check plug and add fluid until it drips. The engine must be running when the check plug is out, or fluid pours out.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Sources: Trick Shift Garage: 2014-2019 Silverado & Sierra 6L80 Transmission Fluid & Filter Change · tahoeyukonforum: Complete Trans Fluid Change (6L80 pump-out method) · GM Tech Info: 6L80 fluid level check (TFT 30-50°C, engine must be running) · 6L80 overhaul fastener specs: pan 9 N·m / 80 lb·in, check plug 25 N·m / 18 lb·ft · Weber State (GM ASEP): no-dipstick fluid level check procedure for 6L80 (86-122°F)
P0700 on this Chevrolet Silverado 1500 — full diagnosis guide →
No owner reports yet — fixed this yourself? tell us how
Same story as the GMT900 trucks: the AFM lifters are under the heads on cylinders 1, 4, 6, and 7. Diagnosis is a compression test on the misfiring cylinder; repair is lifters plus cam inspection, or a full DOD delete.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Sources: tahoeyukonforum: 2014 Silverado 5.3 AFM dead lifter (cyl 6, compression 113 vs 190+) · forum.gon.com: Chevy/GMC lifter crash 5.3/6.2 (multiple owner failures) · ls1tech: L83 lifter collapse (cam + lifters + tune, ~$3k DIY)
P0300 on this Chevrolet Silverado 1500 — full diagnosis guide →
No owner reports yet — fixed this yourself? tell us how
The fix is a fluid exchange done with a flush machine through the cooler lines — not a pan drop. The transmission has no dipstick; level is set via the level-set plug with fluid at the specified temperature.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Sources: gmauthority: TSB 18-NA-355 (Mobil 1 LV ATF HP flush procedure) · tahoeyukonforum: 8-speed shudder TSB discussion (owner results after flush) · cherishyourcar.com: 8L90 shudder, harsh shifts, and why fixes don't stick · TSB 18-NA-355 procedure text (level set plug 80 lb-in, 200-mile effect window)
P0741 on this Chevrolet Silverado 1500 — full diagnosis guide →
No owner reports yet — fixed this yourself? tell us how
The condenser sits ahead of the radiator behind the grille; replacement means discharging the system (a shop must recover the refrigerant — venting it is illegal), swapping the condenser, then vacuum and recharge.
Typical difficulty: Moderate — based on 294 code guides for the cooling repair area (an area-level estimate, not this exact job).
Sources: GPD product info: 2014-2017 condenser leak at drier fitting (gpd #4283C) · scducks forum: 2014+ Silverado A/C condenser leak (common issue, PAG oil at fitting) · YouTube: 2014-2018 Silverado A/C condenser replacement DIY (common problem)
No owner reports yet — fixed this yourself? tell us how
K2XX (Gen V EcoTec3) issue. GM TSB series PIP5382 (B/C/E, NHTSA ID 10083140) states Gen 5 engines L83/L86/LV3 may have an oil-consumption concern of one quart in 2,000 miles; dealer diagnosis is an oil-consumption test. Owner-verified root causes: the driver's-side valve cover PCV baffle misaligned or clogged so liquid oil splashes past it into the intake and is burned (one owner found oil pooling in the intake manifold and cured it by cleaning the valve cover/PCV drain at 148k miles); carboned-up oil control rings from PCV ingestion; and worn oil rings on engines that were worked hard. A 2015 owner reported the oil below the dipstick at 14k miles, then below the add mark again 2,000 miles after a dealer oil change.
Typical difficulty: Moderate — based on 5 code guides for the oil repair area (an area-level estimate, not this exact job).
Sources: TrueDelta: 2015 Silverado 1500 TSB list — PIP5382 (L83/L86/LV3 oil consumption, 1 qt/2000 mi) · silveradosierra.com: 2015 Silverado Oil Consumption Problem (owner: below dipstick at 14k miles) · YouTube: Stop Silverado 5.3L V8 Oil Consumption Permanently (updated valve cover with fixed PCV baffle)
No owner reports yet — fixed this yourself? tell us how
Distinct from the existing 6L80 service note (pan drop / filter / level set) and the 8L90 shudder note: this is the 6L80 torque-converter-clutch shudder. GM PI PIP5337J describes a shake or shudder during light-throttle acceleration between 30 and 65 mph in steady state — on the 6L80 (4.3L V6 / 5.3L V8 K2XX trucks) this is TCC slip in lockup, felt as a rumble-strip vibration or a tachometer 'hunting' 50–100 rpm at steady speed. Documented causes: glazed TCC friction material (converter clutch contacting only in spots, per HP Tuners owners), moisture/contaminated fluid, and the 6L80's transmission-side thermostat holding the trans at ~195°F which accelerates clutch wear. Owner-verified diagnosis: drop the pan — fine silver glitter / gray sludge in the fluid means the converter clutch is shedding and the converter is done; a pan service plus the updated lower-temperature transmission thermostat (the 'flip the pill' fix, later a GM lower-temp thermostat) and a TCC regulator-valve kit (e.g. Transgo) can save a unit whose clutch is not yet glazed.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Sources: silveradosierra.com: 6L80, can it be saved? (TCC failure, pan glitter, converter replacement) · HP Tuners forum: TCC shudder? (2017 Silverado 6L80 lockup shudder, thin converter clutch contact) · GMT Nation: SOLVED! Transmission shudder at 50–60 mph (TCC diagnosis, Lubegard, TCC valve kits) · tahoeyukonforum.com: 6L80 Torque Converter question for newer models (trans thermostat 'flip the pill' / lower-temp thermostat fix)
P0741 on this Chevrolet Silverado 1500 — full diagnosis guide →
No owner reports yet — fixed this yourself? tell us how
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
Score: 97/100 — DIY-friendly
How this is scored (mechanical, no opinion): start at 100; −4 per distinct special tool mentioned in the notes (max −28); −15 per documented dealer-only step (max −30); note-volume band: 15+ notes +10, 8–14 +5, 4–7 +0. Bands: 85+ DIY-friendly · 65–84 DIY with care · 40–64 Experienced DIY only · below 40 Think twice. Pilot rubric — flagged for Robbie’s eyeball before any scale-up.
No NHTSA complaint data in our records for the 2014–2019 Chevrolet Silverado 1500 specifically. See NHTSA data for all Silverado 1500 years →
NHTSA lists no manufacturer communications for the 2014–2019 Chevrolet Silverado 1500 in our pull.
Bulletin pull incomplete: 6 model year(s) failed to load (2014, 2015, 2016, 2017, 2018, 2019).
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.