P2C10: A Camshaft Profile Actuator Position Sensor C Circuit High Bank 1
DIY difficulty 2/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonDriveable - the system simply stays on its default profile.
Your engine switches its A camshaft between lift profiles, and the sensor confirming the switch is giving a bad reading. Expect a check engine light. Usually the sensor or its wiring.
Key facts
P2C10 means a Camshaft Profile Actuator Position Sensor C Circuit High Bank 1. Your engine switches its A camshaft between lift profiles, and the sensor confirming the switch is giving a bad reading. Expect a check engine light. Usually the sensor or its wiring. WrenchFair's published fair-price range for this repair is $60–$250 parts and $100–$300 labor at independent shops.
WrenchFair rates P2C10 a 2-of-5 DIY difficulty (“Sensor testing then replacement; usually accessible on the cylinder head.”) with a “Diagnose soon” driveability rating: Driveable - the system simply stays on its default profile. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
possible flat power delivery
profile switching disabled
Likely causes
Failed profile actuator position sensor C (A camshaft, bank 1 - most common)
Damaged wiring or oil-contaminated connector
Actual actuator fault making the sensor read implausibly
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Read the code with a scan tool and save the freeze-frame data, then check for companion codes - when several sensor codes appear together, suspect a shared reference-voltage or ground problem before any single sensor. Tests: Actual actuator fault making the sensor read implausibly
Check the engine oil level and spec.
Inspect the sensor C wiring and connector. Tests: Damaged wiring or oil-contaminated connector
Watch profile position in live data while the system switches. Tests: Failed profile actuator position sensor C (A camshaft, bank 1 - most common)
Replace the sensor if it reads wrong, clear the code, and confirm switching works.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$60 – $250
Labor$100 – $300
Camshaft profile position sensor C replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2C10 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Sensor testing then replacement; usually accessible on the cylinder head.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →