P212D: Throttle Position Sensor/switch G Circuit High
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonThe PCM enters limp-in mode with acceleration severely limited or disabled, and the throttle can stick. Diagnose immediately.
The throttle position sensor G is reporting abnormally high voltage, so the computer cuts power in limp-in mode.
Model notes: Only used on vehicles with drive-by-wire (DBW) throttle systems.
Key facts
P212D means throttle Position Sensor/switch G Circuit High. The throttle position sensor G is reporting abnormally high voltage, so the computer cuts power in limp-in mode. WrenchFair's published fair-price range for this repair is $50–$400 parts and $75–$350 labor at independent shops.
WrenchFair rates P212D a 3-of-5 DIY difficulty (“Visual wiring inspection and DVOM voltage tests are intermediate; an oscilloscope helps catch voltage spikes.”) with a “Diagnose soon” driveability rating: The PCM enters limp-in mode with acceleration severely limited or disabled, and the throttle can stick. Diagnose immediately. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
stuck throttle (at any rpm)
limited or no acceleration
engine stall when allowed to idle
hesitation when accelerating
cruise control inoperative
Likely causes
Open or shorted circuits between the TPS, PPS, and the PCM
Defective TPS or PPS
Corroded electrical connectors
Faulty drive-by-wire actuator motor
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check technical service bulletins for the vehicle in question.
Visually inspect all system-related wiring and connectors; check the throttle plate for carbon buildup or damage. Excessive carbon holding the throttle body open at startup can set P212D - clean carbon per manufacturer recommendations. Tests: Corroded electrical connectors
Connect the scanner and retrieve all stored codes plus freeze frame data; write them down in order stored, then clear the codes and test-drive.
Narrow the scanner data stream to pertinent data and watch for voltage spikes and inconsistencies between the TPS, PPS, and PCM. Tests: Open or shorted circuits between the TPS, PPS, and the PCM
If no spikes are seen, use the DVOM to retrieve live data at each sensor individually; look for spikes while actuating the throttle slowly from closed to wide open (usually 0.5 volts closed to 4.5 volts wide open). Suspect the sensor being tested if spikes appear.
Some manufacturers require the throttle body, throttle actuator motor, and all throttle position sensors be replaced together.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$50 – $400
Labor$75 – $350
Throttle body / sensor assembly replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P212D ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Visual wiring inspection and DVOM voltage tests are intermediate; an oscilloscope helps catch voltage spikes.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →