P2070: Intake manifold tuning (IMT) valve stuck open bank 1
DIY difficulty 4/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonYou can drive, but fuel economy and performance suffer - and in rare cases loose hardware can be drawn into a cylinder, so get it fixed promptly.
The intake air flaps on bank 1 (the side with cylinder 1) are stuck open - usually carbon buildup binding the flaps, a failed actuator, or a vacuum leak. Fuel economy and performance suffer.
Key facts
P2070 means intake manifold tuning (IMT) valve stuck open bank 1. The intake air flaps on bank 1 (the side with cylinder 1) are stuck open - usually carbon buildup binding the flaps, a failed actuator, or a vacuum leak. Fuel economy and performance suffer. WrenchFair's published fair-price range for this repair is $150–$700 parts and $200–$600 labor at independent shops.
WrenchFair rates P2070 a 4-of-5 DIY difficulty (“Carbon cleaning of the flaps can be DIY with the manifold accessible; actuator replacement and circuit testing need the factory specs.”) with a “Diagnose soon” driveability rating: You can drive, but fuel economy and performance suffer - and in rare cases loose hardware can be drawn into a cylinder, so get it fixed promptly. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
diminished fuel efficiency
reduced engine performance
lean or rich exhaust codes
no symptoms at all may be exhibited
Likely causes
Binding or loose IMT flaps (carbon buildup) (most common)
Defective IMT actuator (valve)
Vacuum leak
Open or shorted wiring or connectors
Faulty PCM or a PCM programming error (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 7 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check for technical service bulletins for your make and model.
Retrieve all codes and freeze-frame data, record it, clear the codes, and drive to see if P2070 resets.
Inspect the IMT linkage and flaps for binding, carbon buildup, and broken bushings. Tests: Binding or loose IMT flaps (carbon buildup) (most common)
Test voltage, ground, and signal circuits at the bank 1 IMT valve against the factory specs.
Test the IMT valve itself against the factory specs and replace it if it fails.
If the valve is functional, test the input and output signal circuits from the fuse panel and PCM with the controllers disconnected.
Only suspect the PCM after the valve, linkage, and wiring are all proven good.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$150 – $700
Labor$200 – $600
IMT actuator or linkage repair. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2070 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Carbon cleaning of the flaps can be DIY with the manifold accessible; actuator replacement and circuit testing need the factory specs.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →