P2020: Intake manifold runner position sensor/switch circuit range/performance (bank 2)
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonSafe to drive, but weak power and misfires will get worse if the flaps are mechanically sticking - do not let it become a stuck-flap problem.
The sensor watching the little air-shaping flaps on the non-cylinder-1 side is reporting a position that does not make sense - out of range or not moving when commanded. Usually the sensor, a sticking flap, or wiring. Expect weak power, occasional misfires, and worse mileage.
Key facts
P2020 means intake manifold runner position sensor/switch circuit range/performance (bank 2). The sensor watching the little air-shaping flaps on the non-cylinder-1 side is reporting a position that does not make sense - out of range or not moving when commanded. Usually the sensor, a sticking flap, or wiring. Expect weak power, occasional misfires, and worse mileage. WrenchFair's published fair-price range for this repair is $30–$600 parts and $150–$600 labor at independent shops.
WrenchFair rates P2020 a 3-of-5 DIY difficulty (“Connector checks are easy, but proving the sensor signal is out of range needs live data or a multimeter plus the factory chart, and a binding flap check can require intake removal.”) with a “Diagnose soon” driveability rating: Safe to drive, but weak power and misfires will get worse if the flaps are mechanically sticking - do not let it become a stuck-flap problem. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
lack of power
occasional misfire
poor fuel economy
Likely causes
Sticking or faulty bank 2 IMRC valve from carbon deposits around the flaps (most common)
Faulty bank 2 IMRC actuator/position sensor
Corroded, burnt, or loose terminals in the sensor connector
Chafed or damaged wiring in the sensor circuit
Sticking throttle plates or intake/vacuum leaks setting companion codes - diagnose those first
Failed PCM (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check for technical service bulletins for your make and model, and diagnose any other intake or engine-performance codes first - they can set this one as a side effect. Tests: Sticking throttle plates or intake/vacuum leaks setting companion codes - diagnose those…
Confirm there are no intake or exhaust leaks, which can skew the readings. Tests: Sticking throttle plates or intake/vacuum leaks setting companion codes - diagnose those…
Locate the bank 2 IMRC valve/sensor and inspect the connector and wiring for rubbing, bare wires, melted plastic, and corroded terminals; clean, pack with dielectric compound, reassemble, clear the code, and retest. Tests: Corroded, burnt, or loose terminals in the sensor connector
Watch the IMRC sensor signal on a scan tool while snapping the throttle - the signal should change smoothly with RPM per the factory chart. Tests: Faulty bank 2 IMRC actuator/position sensor
Remove the IMRC sensor/actuator and move the flap linkage by hand (watch for a strong return spring) to check for binding or looseness.
If the flaps move freely but the signal is still out of range, replace the sensor/actuator; if the plates bind, the intake manifold usually needs replacement.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$30 – $600
Labor$150 – $600
IMRC position sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2020 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Connector checks are easy, but proving the sensor signal is out of range needs live data or a multimeter plus the factory chart, and a binding flap check can require intake removal.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →