P2016: Intake manifold runner position sensor/switch circuit low (bank 1)
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonSafe to drive, but you will feel weak power and burn more fuel - and a wrong position reading can mask a real mechanical flap problem.
A sensor that tells the computer where the little air-shaping flaps inside your intake are sitting is reading too low a voltage on the cylinder-1 side. Usually a bad sensor, corroded connector, or damaged wire. Expect the check engine light, weak power, and worse mileage.
Key facts
P2016 means intake manifold runner position sensor/switch circuit low (bank 1). A sensor that tells the computer where the little air-shaping flaps inside your intake are sitting is reading too low a voltage on the cylinder-1 side. Usually a bad sensor, corroded connector, or damaged wire. Expect the check engine light, weak power, and worse mileage. WrenchFair's published fair-price range for this repair is $30–$350 parts and $120–$450 labor at independent shops.
WrenchFair rates P2016 a 3-of-5 DIY difficulty (“Connector inspection and cleaning is easy; voltage testing needs a multimeter and the factory wiring diagram, and deeper diagnosis can require intake manifold removal.”) with a “Diagnose soon” driveability rating: Safe to drive, but you will feel weak power and burn more fuel - and a wrong position reading can mask a real mechanical flap problem. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
lack of power
poor fuel economy
Likely causes
Corroded, burnt, or loose terminals in the IMRC sensor connector (most common - inspect and clean first)
Faulty bank 1 IMRC actuator/position sensor
Short to ground or damaged wiring in the sensor circuit
Faulty IMRC actuator relay (if equipped)
Failed PCM (rare - only after everything else is ruled out)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check for technical service bulletins for your make and model before touching anything.
Locate the bank 1 IMRC valve/sensor on the intake manifold and visually inspect the connector and wiring for rubbing, bare wires, melted plastic, or corroded terminals. Tests: Corroded, burnt, or loose terminals in the IMRC sensor connector (most common - inspect…
Clean any suspect terminals with electrical contact cleaner, pack the connector with dielectric silicone compound, reassemble, clear the code, and see if it returns. Tests: Corroded, burnt, or loose terminals in the IMRC sensor connector (most common - inspect…
If it returns, test the sensor power and ground circuits with a multimeter per the factory wiring diagram - a missing supply voltage points at the circuit, not the sensor. Tests: Short to ground or damaged wiring in the sensor circuit
Use a scan tool actuator test to command the IMRC valve open and closed while watching position feedback; if the scan tool cannot move the valve, suspect the ground circuit or the PCM.
Replace only the component that fails testing - do not condemn the PCM until every other possibility is exhausted.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$30 – $350
Labor$120 – $450
IMRC position sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2016 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Connector inspection and cleaning is easy; voltage testing needs a multimeter and the factory wiring diagram, and deeper diagnosis can require intake manifold removal.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →