P2013: Intake Manifold Runner Control Circuit High Bank 2
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonHesitation and low-RPM performance loss; not an immediate breakdown risk, but diagnose and fix before driveability worsens.
The bank 2 intake runner flaps (the small doors that tune airflow into the engine) are getting too much voltage on their control circuit.
Model notes: Applies to Nissan, Honda, Infiniti, Ford, Dodge, Acura, Toyota. On some models the IMRC actuator uses a vacuum diaphragm with a PCM-controlled electronic solenoid.
Key facts
P2013 means intake Manifold Runner Control Circuit High Bank 2. The bank 2 intake runner flaps (the small doors that tune airflow into the engine) are getting too much voltage on their control circuit. WrenchFair's published fair-price range for this repair is $50–$250 parts and $75–$300 labor at independent shops.
WrenchFair rates P2013 a 3-of-5 DIY difficulty (“Wiring and resistance tests are intermediate; actuator/sensor access varies by vehicle.”) with a “Diagnose soon” driveability rating: Hesitation and low-RPM performance loss; not an immediate breakdown risk, but diagnose and fix before driveability worsens. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
hesitation upon acceleration
reduction in engine performance, especially at low rpm
rich or lean exhaust
diminished fuel efficiency
engine surge
Likely causes
Loose or binding intake manifold runners bank 2
Defective IMRC actuator solenoid bank 2
Bad intake manifold runner position sensor bank 2
Open or shorted wiring in the IMRC actuator solenoid control circuit
Carbon buildup on the IMRC flaps or intake manifold ports bank 2
Faulty MAP sensor
Corroded IMRC actuator solenoid connector face
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 7 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check technical service bulletins for the symptoms, stored codes, and vehicle in question.
Retrieve stored codes and freeze frame data, record them, clear codes, and test-drive to see if the code resets.
Visually inspect system wiring and connector faces; IMRC actuator connectors are prone to corrosion. Tests: Corroded IMRC actuator solenoid connector face
Access the IMRC actuator solenoid and runner position sensor and use the DVOM to perform resistance tests on both; replace either component that fails to meet manufacturer specs, then retest. Tests: Defective IMRC actuator solenoid bank 2
To prevent PCM damage, disconnect all related controllers before testing circuit resistance with the DVOM.
If actuator and sensor resistance are within spec, use the DVOM to test resistance and continuity on all system circuits.
Test for IMRC flap binding with the actuator disconnected from the shaft; check for carbon coking inside the intake manifold walls and for loose flap screws or rivets.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$50 – $250
Labor$75 – $300
IMRC actuator solenoid or runner position sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2013 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Wiring and resistance tests are intermediate; actuator/sensor access varies by vehicle.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →