P2008: Intake manifold runner control circuit open (bank 1)
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonSafe to drive - this is usually a soft code - but a stuck or broken swirl flap can shed hardware into the engine, so confirm the flaps themselves are intact.
There is a broken wire or dead electrical connection in the circuit that controls the little air-shaping flaps inside your intake on the cylinder-1 side. The flaps are probably fine - the computer just cannot talk to their motor or valve. Expect a rough idle, surging, and slightly weaker low-end pull.
Key facts
P2008 means intake manifold runner control circuit open (bank 1). There is a broken wire or dead electrical connection in the circuit that controls the little air-shaping flaps inside your intake on the cylinder-1 side. The flaps are probably fine - the computer just cannot talk to their motor or valve. Expect a rough idle, surging, and slightly weaker low-end pull. WrenchFair's published fair-price range for this repair is $40–$600 parts and $120–$500 labor at independent shops.
WrenchFair rates P2008 a 3-of-5 DIY difficulty (“Electrical checks are straightforward, but reaching the solenoid often means working around a hot, crowded intake; some vehicles have a known reprogram fix, so check bulletins first.”) with a “Diagnose soon” driveability rating: Safe to drive - this is usually a soft code - but a stuck or broken swirl flap can shed hardware into the engine, so confirm the flaps themselves are intact. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on, sometimes blinking on and off as the fault comes and goes
rougher than normal idle
engine surge at times
slight reduction in low-end torque
Likely causes
Failed IMRC / swirl-flap solenoid valve, heat-soaked and fouled by dirt and EGR soot (most common)
Open or shorted wiring in the bank 1 IMRC solenoid control circuit
Corroded or loose electrical connector at the solenoid
Cracked or disconnected vacuum lines on vacuum-operated systems
Swirl flaps gummed with EGR soot and stuck in place
A failing MAF sensor or EGR valve setting companion codes - diagnose those first if present
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check for technical service bulletins - some vehicles (including certain Audis) fix this with an ECM reprogram.
Inspect the vacuum hoses for cracks and the electrical connector on the solenoid for corrosion or a loose fit. Tests: Corroded or loose electrical connector at the solenoid
With a scan tool, run the solenoid operational test and command it open and closed; if it does not respond, the valve is bad. Tests: Failed IMRC / swirl-flap solenoid valve, heat-soaked and fouled by dirt and EGR soot…
If the valve works but the actuating rod barely moves, the intake manifold flaps are gummed or the manifold needs replacement. Tests: Failed IMRC / swirl-flap solenoid valve, heat-soaked and fouled by dirt and EGR soot…
If the solenoid is dead, test continuity between the harness connector and the fuse/relay feeds with an ohmmeter per the service manual.
If a MAF or EGR code is stored alongside this one, diagnose and repair that code first, then clear and retest.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$40 – $600
Labor$120 – $500
IMRC solenoid valve replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2008 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Electrical checks are straightforward, but reaching the solenoid often means working around a hot, crowded intake; some vehicles have a known reprogram fix, so check bulletins first.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →