P2005: Intake manifold runner control stuck open (bank 2)
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonSafe to drive short term, but expect weak low-end response and worse mileage until the flaps move freely again.
Inside your intake there are little flaps that shape airflow at low engine speeds, and the ones on the non-cylinder-1 side of the engine are stuck in the open position. The car runs, but low-speed power and gas mileage suffer, and the engine may surge.
Key facts
P2005 means intake manifold runner control stuck open (bank 2). Inside your intake there are little flaps that shape airflow at low engine speeds, and the ones on the non-cylinder-1 side of the engine are stuck in the open position. The car runs, but low-speed power and gas mileage suffer, and the engine may surge. WrenchFair's published fair-price range for this repair is $40–$400 parts and $150–$450 labor at independent shops.
WrenchFair rates P2005 a 3-of-5 DIY difficulty (“Reaching the actuator and linkage often means removing intake components; the mechanical binding check itself is straightforward once you have access.”) with a “Diagnose soon” driveability rating: Safe to drive short term, but expect weak low-end response and worse mileage until the flaps move freely again. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
reduction in engine performance, especially at low rpm
diminished fuel efficiency
engine surge
Likely causes
Carbon coking inside the intake manifold binding the runner flaps (most common)
Defective bank 2 IMRC actuator solenoid
Loose, binding, or detached runner flaps on the linkage shaft (loose screws or rivets)
Bad bank 2 IMRC runner position sensor
Corroded IMRC actuator connector face or open/shorted wiring in the solenoid control circuit
Faulty MAP sensor feeding bad feedback to the computer
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check for technical service bulletins for your make and model - several have known IMRC fixes.
Inspect the bank 2 IMRC actuator and its connector face for corrosion, bent pins, and damaged wiring. Tests: Corroded IMRC actuator connector face or open/shorted wiring in the solenoid control…
With a scan tool, command the actuator and watch the runner position sensor feedback to confirm the flaps are not responding. Tests: Bad bank 2 IMRC runner position sensor
Disconnect the actuator from the linkage shaft and move the runner flaps by hand to feel for binding or a detached flap. Tests: Loose, binding, or detached runner flaps on the linkage shaft (loose screws or rivets)
If binding, inspect for carbon buildup inside the manifold and for loose flap screws or rivets; clean or repair as needed.
If the mechanics move freely, test the actuator solenoid and position sensor against the factory specs, then check circuit continuity with the controllers disconnected to avoid damage.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$40 – $400
Labor$150 – $450
Intake cleaning or IMRC actuator replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2005 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Reaching the actuator and linkage often means removing intake components; the mechanical binding check itself is straightforward once you have access.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →