P0E68: Battery Charger Control Circuit Range/Performance
DIY difficulty 2/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonYou may be unable to charge; the car is usually still drivable on its remaining charge - plan charging before it runs out.
The battery charger control is sending readings that don't make sense for what the car is actually doing. The car may refuse to charge or stop charging partway; it is usually still drivable on its remaining charge.
Key facts
P0E68 means battery Charger Control Circuit Range/Performance. The battery charger control is sending readings that don't make sense for what the car is actually doing. The car may refuse to charge or stop charging partway; it is usually still drivable on its remaining charge. WrenchFair's published fair-price range for this repair is $20–$250 parts and $100–$300 labor at independent shops.
WrenchFair rates P0E68 a 2-of-5 DIY difficulty (“This is a low-voltage signal circuit - diagnosis is multimeter and scan-tool work with no high-voltage exposure.”) with a “Diagnose soon” driveability rating: You may be unable to charge; the car is usually still drivable on its remaining charge - plan charging before it runs out. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
vehicle will not charge
charging stops partway
charge warning light on
Likely causes
sensor reading skewed out of expected range (most common)
excess resistance from corroded wiring or connectors
mechanical issue in the monitored component
control module fault (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
1. Clear the code and confirm it returns under the same conditions before replacing anything.
2. Inspect the battery charger control connector and wiring for damage, corrosion, water intrusion, or pins pushed back out of the connector body - pay attention to spots where the harness flexes or rubs. Tests: excess resistance from corroded wiring or connectors
3. With a scan tool, watch the live battery charger control reading while wiggling the harness; a reading that jumps or drops out confirms a wiring or connector fault. Tests: excess resistance from corroded wiring or connectors
4. Check the battery charger control power, ground, and signal wiring for opens and shorts per the factory service manual before condemning the part. Tests: control module fault (rare)
5. If the wiring tests good, replace the battery charger control sensor or component, then retest.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$20 – $250
Labor$100 – $300
Sensor reading skewed out of expected range. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0E68 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — This is a low-voltage signal circuit - diagnosis is multimeter and scan-tool work with no high-voltage exposure.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →