P0E60: Battery Charge Mode Control Circuit Range/Performance
DIY difficulty 4/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonThe car will usually limit power or refuse ready mode until the pack checks out - plan on a tow if it will not start.
The battery charge mode control is sending readings that don't make sense for what the car is actually doing. Expect a warning light with reduced power, or the car may refuse to go into ready mode at all.
Key facts
P0E60 means battery Charge Mode Control Circuit Range/Performance. The battery charge mode control is sending readings that don't make sense for what the car is actually doing. Expect a warning light with reduced power, or the car may refuse to go into ready mode at all. WrenchFair's published fair-price range for this repair is $90–$460 parts and $40–$360 labor at independent shops.
WrenchFair rates P0E60 a 4-of-5 DIY difficulty (“High-voltage system: lethal voltage in the pack and orange cables - pack and inverter internals are qualified-technician-only work, and DIY is limited to visual checks, fuses, and 12V-side testing.”) with a “Diagnose soon” driveability rating: The car will usually limit power or refuse ready mode until the pack checks out - plan on a tow if it will not start. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
warning light on
reduced power or limp mode
vehicle may not enter ready mode
Likely causes
mode switch contacts aged (most common)
high-resistance contact
sensor element aged beyond calibration window
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
1. HIGH-VOLTAGE SAFETY FIRST: this code touches the traction-battery high-voltage system. Lethal voltage lives in the pack and the orange cables - pack internals are qualified-technician-only work. DIY is limited to visual inspection, fuses, and 12V-side checks with the system depowered.
2. Clear the code and confirm it returns under the same conditions before replacing anything.
3. Inspect the battery charge mode control connector and wiring for damage, corrosion, water intrusion, or pins pushed back out of the connector body - pay attention to spots where the harness flexes or rubs.
4. With a scan tool, watch the live battery charge mode control reading while wiggling the harness; a reading that jumps or drops out confirms a wiring or connector fault.
5. Check the battery charge mode control power, ground, and signal wiring for opens and shorts per the factory service manual before condemning the part.
6. If the wiring tests good, replace the battery charge mode control sensor or component, then retest.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$90 – $460
Labor$40 – $360
Mode switch contacts aged. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0E60 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — High-voltage system: lethal voltage in the pack and orange cables - pack and inverter internals are qualified-technician-only work, and DIY is limited to visual checks, fuses, and 12V-side testing.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →