P0D91: Battery Charger Coupler Lock Control Circuit/Open
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonYou may be unable to charge; the car is usually still drivable on its remaining charge - plan charging before it runs out.
A wire or plug in the battery charger coupler lock circuit is broken or unplugged, so the car's computer can't see what that part is doing. The car may refuse to charge or stop charging partway; it is usually still drivable on its remaining charge.
Key facts
P0D91 means battery Charger Coupler Lock Control Circuit/Open. A wire or plug in the battery charger coupler lock circuit is broken or unplugged, so the car's computer can't see what that part is doing. The car may refuse to charge or stop charging partway; it is usually still drivable on its remaining charge. WrenchFair's published fair-price range for this repair is $170–$920 parts and $70–$540 labor at independent shops.
WrenchFair rates P0D91 a 3-of-5 DIY difficulty (“This is a low-voltage signal circuit - diagnosis is multimeter and scan-tool work with no high-voltage exposure.”) with a “Diagnose soon” driveability rating: You may be unable to charge; the car is usually still drivable on its remaining charge - plan charging before it runs out. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
warning light on
charge status indicator shows fault
charging may not start or interrupts
slower-than-expected charge rate
Likely causes
open in actuator control wire (most common)
open lock actuator
pin pushed back out of connector body
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
1. Clear the code and confirm it returns under the same conditions before replacing anything.
2. Inspect the battery charger coupler lock connector and wiring for damage, corrosion, water intrusion, or pins pushed back out of the connector body - pay attention to spots where the harness flexes or rubs. Tests: pin pushed back out of connector body
3. With a scan tool, watch the live battery charger coupler lock reading while wiggling the harness; a reading that jumps or drops out confirms a wiring or connector fault. Tests: pin pushed back out of connector body
4. Check the battery charger coupler lock power, ground, and signal wiring for opens and shorts per the factory service manual before condemning the part. Tests: open lock actuator
5. If the wiring tests good, replace the battery charger coupler lock sensor or component, then retest.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$170 – $920
Labor$70 – $540
Repairing the open in the battery charger coupler lock wiring. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0D91 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — This is a low-voltage signal circuit - diagnosis is multimeter and scan-tool work with no high-voltage exposure.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →