P0CCB: Charge port door A open request switch circuit intermittent/erratic
DIY difficulty 2/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonYou can usually drive normally, but charging may fail or stop early — sort it before you need a charge.
The charge-port door has a small sensor that tells the car whether the door is open or closed, and this code means that sensor signal is cutting in and out. The door sensor itself is harmless low-voltage stuff, but the charge port it guards connects to the high-voltage battery — check the door for ice, dirt, or a sticking hinge before anything else.
Key facts
P0CCB means charge port door A open request switch circuit intermittent/erratic. The charge-port door has a small sensor that tells the car whether the door is open or closed, and this code means that sensor signal is cutting in and out. The door sensor itself is harmless low-voltage stuff, but the charge port it guards connects to the high-voltage battery — check the door for ice, dirt, or a sticking hinge before anything else. WrenchFair's published fair-price range for this repair is $50–$100 parts and $50–$225 labor at independent shops.
WrenchFair rates P0CCB a 2-of-5 DIY difficulty (“Beginner-friendly checks (fuses, connectors, cleaning) are DIY; stop there if the fault is inside the high-voltage system.”) with a “Diagnose soon” driveability rating: You can usually drive normally, but charging may fail or stop early — sort it before you need a charge. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
charge status indicator shows fault
charging may not start or interrupts
slower-than-expected charge rate
Likely causes
connector not fully seated
noisy or corroded ground connection
connector with intermittent contact under vibration
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Park, power down completely, and respect the high-voltage system: the battery pack and orange cables are lethal to touch. Leave anything inside the pack to a trained technician; you can safely check the 12V battery, fuses, and connectors outside the pack. Tests: connector not fully seated
Clear ice, dirt, or debris from the door and hinge, then work the door by hand to feel for sticking or binding.
Lubricate the hinge and latch with silicone spray.
Inspect the door sensor/switch connector in the charge-port area for corrosion or loose pins. Tests: connector not fully seated
If the door, hinge, or actuator is physically damaged, replacement is a trim-level DIY or a quick shop job.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$50 – $100
Labor$50 – $225
connector not fully seated. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0CCB ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Beginner-friendly checks (fuses, connectors, cleaning) are DIY; stop there if the fault is inside the high-voltage system.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →