P0706: Transmission range sensor implausible signal (F125)
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonMay enter limp mode or fail to restart. Get it checked soon.
The transmission range/position sensor signal does not make sense to the TCU. Symptoms range from a lit gear display to full limp mode.
VW/Audi note (VCDS): Watch the F125 position bits in measuring blocks while shifting P-R-N-D - all positions should read cleanly.
Model notes: This matches one of the A7's August 2026 faults. The F125 lives low on the transmission where road water reaches it - corrosion is the bet, not the switch itself.
Key facts
P0706 means transmission range sensor implausible signal (F125). The transmission range/position sensor signal does not make sense to the TCU. Symptoms range from a lit gear display to full limp mode. WrenchFair's published fair-price range for this repair is $60–$200 parts and $150–$350 labor at independent shops.
WrenchFair rates P0706 a 3-of-5 DIY difficulty (“Connector cleaning is easy; switch replacement is under the car.”) with a “Diagnose soon” driveability rating: May enter limp mode or fail to restart. Get it checked soon. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
all gear indicators lit
limp mode
stuck in one gear
harsh shifting
gear display flashing
engine can start in any gear
vehicle may start moving as soon as engine starts
Likely causes
Corroded F125 multifunction switch connector (very common - Audi TSB 37 13 92 documents pin corrosion)
Worn F125 switch
TCU internal fault misreading the sensor
Wiring damage
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 3 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Inspect the F125 connector for water/corrosion FIRST - cleaning fixes many of these Tests: Corroded F125 multifunction switch connector (very common - Audi TSB 37 13 92 documents…
Read the sensor values in VCDS while moving the shifter through all positions
Check TCU pins for corrosion before replacing the switch Tests: Corroded F125 multifunction switch connector (very common - Audi TSB 37 13 92 documents…
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$60 – $200
Labor$150 – $350
Sensor replacement; connector cleaning is nearly free. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0706-VAG ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Connector cleaning is easy; switch replacement is under the car.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →