P0548: Exhaust Gas Temperature Sensor Circuit Low (Bank 2 Sensor 1)
DIY difficulty 2/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonDrivable but often down on power; DPF damage is possible if regeneration cannot be controlled.
Your diesel has temperature sensors in the exhaust for the turbo and DPF systems, and the bank 2 sensor 1 signal is wrong. They live in extreme heat, so the sensor dying or its wiring cooking is usual. Check the wiring first - it is cheaper than the sensor.
Key facts
P0548 means exhaust Gas Temperature Sensor Circuit Low (Bank 2 Sensor 1). Your diesel has temperature sensors in the exhaust for the turbo and DPF systems, and the bank 2 sensor 1 signal is wrong. They live in extreme heat, so the sensor dying or its wiring cooking is usual. Check the wiring first - it is cheaper than the sensor. WrenchFair's published fair-price range for this repair is $80–$250 parts and $100–$250 labor at independent shops.
WrenchFair rates P0548 a 2-of-5 DIY difficulty (“The sensor unscrews from the exhaust but is often seized; penetrating oil and heat help.”) with a “Diagnose soon” driveability rating: Drivable but often down on power; DPF damage is possible if regeneration cannot be controlled. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
reduced engine power
DPF regeneration problems
poor turbo response
Likely causes
failed EGT sensor
wiring damaged by exhaust heat
corroded or loose connector
soot-fouled sensor tip
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
Watch the bank 2 EGT readings with live data - the stuck or impossible one is bad.
Inspect the wiring for heat damage. Tests: wiring damaged by exhaust heat
With the key on and engine off, check the reference voltage and ground at the component connector with a multimeter. Tests: corroded or loose connector
Replace the sensor if the wiring is good; use anti-seize on the new one.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$80 – $250
Labor$100 – $250
Exhaust gas temperature sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0548 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — The sensor unscrews from the exhaust but is often seized; penetrating oil and heat help.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →