Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonYour regular brakes keep working normally, but ABS, traction control, and stability control are probably disabled until this is fixed. Drive gently on wet or slippery roads.
The electric pump inside your ABS unit that powers anti-lock braking isn't working right. Your normal brakes work fine, but ABS, traction control, and stability control are switched off.
Key facts
C0268 means brake Pump Run Time Exceeded. The electric pump inside your ABS unit that powers anti-lock braking isn't working right. Your normal brakes work fine, but ABS, traction control, and stability control are switched off. WrenchFair's published fair-price range for this repair is $350–$1100 parts and $200–$550 labor at independent shops.
WrenchFair rates C0268 a 5-of-5 DIY difficulty (“Checking fuses, relays, and connections is easy DIY; replacing the unit means brake lines and a full bleed.”) with a “Diagnose soon” driveability rating: Your regular brakes keep working normally, but ABS, traction control, and stability control are probably disabled until this is fixed. Drive gently on wet or slippery roads. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
abs warning light on
traction control or stability control light on
abs pump self-test noise missing at key-on
cruise control stops working
Likely causes
pump motor seized, often after the car sat unused for a long stretch
pump relay failed or welded (where the relay is serviceable separately)
corroded power or ground connection at the hydraulic unit
wiring fault in the pump motor circuit
ABS module driver fault is possible but uncommon - check power, ground, and the relay first
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
1. Turn the key on (engine off) and listen at the hydraulic unit: you should hear the pump run its brief self-test. Silence points at the motor or its power supply. Tests: corroded power or ground connection at the hydraulic unit
2. Check the ABS pump fuse and relay in the under-hood fuse box, including the socket for corrosion. Tests: pump relay failed or welded (where the relay is serviceable separately)
3. Inspect the heavy power and ground wires at the hydraulic control unit for corrosion, looseness, or heat damage. Tests: corroded power or ground connection at the hydraulic unit
4. With a scan tool, try commanding the pump motor on through ABS bidirectional controls. Tests: pump motor seized, often after the car sat unused for a long stretch
5. If power and ground are good but the motor won't run, the pump motor (usually serviced as part of the hydraulic unit) needs replacement, followed by a brake bleed.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$350 – $1100
Labor$200 – $550
A remanufactured hydraulic unit with pump, roughly $700-$1,500 installed with a brake bleed. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for C0268 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
5 of 5 — Checking fuses, relays, and connections is easy DIY; replacing the unit means brake lines and a full bleed.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →