B0038: Second row right side airbag deployment control circuit fault
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonThe car drives normally, but the affected restraint may not protect you in a crash - get it diagnosed promptly.
Your car's airbag computer found an electrical problem in the wiring that fires the second-row right side airbag. The airbag warning light will stay on, and that side airbag may not deploy in a crash. The car still drives normally.
Key facts
B0038 means second row right side airbag deployment control circuit fault. Your car's airbag computer found an electrical problem in the wiring that fires the second-row right side airbag. The airbag warning light will stay on, and that side airbag may not deploy in a crash. The car still drives normally. WrenchFair's published fair-price range for this repair is $150–$600 parts and $150–$350 labor at independent shops.
WrenchFair rates B0038 a 3-of-5 DIY difficulty (“Airbag work demands a battery disconnect plus a waiting period; under-seat harnesses are the usual culprit and are inspected with basic hand tools and a multimeter.”) with a “Diagnose soon” driveability rating: The car drives normally, but the affected restraint may not protect you in a crash - get it diagnosed promptly. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
airbag warning light on
srs service message on the dash
Likely causes
Damaged wiring or a loose/corroded connector in the second row right side airbag circuit (most common - under-seat and seatback harnesses get kicked, pinched by seat tracks, or soaked)
Failed side airbag module in the second-row right seatback
Water intrusion corroding a connector along the circuit
Poor repair or disturbed connector from previous seat or upholstery work
Restraints control module fault (rare - diagnose everything else first)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Disconnect the battery (negative terminal first) and wait at least 10 minutes before touching any SRS connector or component. Tests: Damaged wiring or a loose/corroded connector in the second row right side airbag circuit…
Read the code with an SRS-capable scan tool and note any subcode digits after the main code (e.g. -11, -12, -13) - many makes append them to say open circuit, short to ground, short to battery, or wires shorted together. Tests: Damaged wiring or a loose/corroded connector in the second row right side airbag circuit…
With power still off, inspect the second-row right seatback side bolster wiring and connectors - slide the seat fully forward and back to expose the under-seat harness and check for pinching, chafing, or corrosion. Tests: Damaged wiring or a loose/corroded connector in the second row right side airbag circuit…
Unplug and inspect the side-airbag connector (usually yellow) for bent pins, moisture, or green corrosion; clean or repair as needed. Tests: Damaged wiring or a loose/corroded connector in the second row right side airbag circuit…
Test the circuit only with the battery disconnected and only per the factory service manual's SRS procedure - never apply power to or probe a live deployment circuit.
Verify the restraints control module's power and ground feeds, repair the fault, reconnect the battery, clear the code, and confirm the airbag light completes its power-on self-test.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$150 – $600
Labor$150 – $350
Wiring/connector repair under the seat, or side airbag module replacement if the module itself failed. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for B0038 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Airbag work demands a battery disconnect plus a waiting period; under-seat harnesses are the usual culprit and are inspected with basic hand tools and a multimeter.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →