Community-sourced DIY repair guides for the 2014–2019 Toyota Highlander, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
The 12V battery sits in the engine bay on the driver side -- an easy 10mm-socket job. Loosen the hold-down bracket (the front bolt comes out fully; the other side is a J-hook you just loosen and swing aside), then remove the negative cable first and the positive second. Drop the new battery in the same orientation (positive terminal toward the back-left as viewed from the front), then reconnect positive first, negative last, and re-seat the hold-down. Owners note the vehicle may take a couple of crank attempts to start right after a battery swap, per the owner's manual.
Typical difficulty: Involved — based on 854 code guides for the battery repair area (an area-level estimate, not this exact job).
Torque specs
Battery cable clamps: verify — Snug -- do not over-tighten and crack the battery posts; confirm spec in factory service info if needed.
Tips
Match the battery size carefully -- owners warn that a shorter-than-stock battery won't sit right in the tray, misaligns the terminals, and defeats the hold-down clamp. Group 24F is the common US fitment.
No radio code needed -- unlike older Hondas, there's no anti-theft lockout to worry about on a battery swap here.
Expect some electronic quirks on first start (idle relearn, power windows needing re-initialization) -- they clear with a short drive.
Auto start/stop equipped models (2017+) eat batteries faster -- owners report dead batteries at 3.5 years and recommend testing annually once you're past year 3.
Clean any corrosion off the cable terminals and tray with a wire brush while the battery is out.
Straightforward floating-caliper front brakes: jack and support the front, pull the wheel, unbolt the caliper (hang it from the strut -- don't let it dangle on the hose), and slide the pads out of the bracket. The caliper bracket comes off for rotor replacement; front rotors are 328mm and can be rust-seized to the hub, so expect to persuade them. The full job -- pads and rotors, both fronts -- is a standard afternoon driveway job covered by multiple Highlander-specific walkthroughs (1A Auto/TRQ has a full 2014-2019 step-by-step).
Typical difficulty: Moderate — based on 265 code guides for the brake repair area (an area-level estimate, not this exact job).
Torque specs
Lug nuts: verify — Confirm against the owner's manual/factory service info -- always torque wheels with a torque wrench.
Caliper and bracket bolts: verify — Confirm against factory service info; these are safety-critical fasteners.
Tips
Wire-brush the caliper slide pins and hub face and use proper silicone brake lubricant on the pins -- dry or corroded pins are what cause uneven pad wear on these trucks.
If a rotor won't break free from the hub, owners thread two M8 bolts into the rotor's puller holes to walk it off -- don't hammer the rotor face.
Compress the caliper pistons with a proper compressor or C-clamp, and crack the master cylinder cap first so the displaced fluid has somewhere to go.
Watch the ABS wheel-speed sensor wire at the knuckle while the caliper and bracket are off -- snagging it is the one easy way to turn a brake job into a C0035 code.
Do a proper bed-in: a series of moderate stops from 35-45 mph, then drive without dragging the brakes so the rotors cool evenly -- skips the 'warped rotor' vibration complaints.
On the 2GR-FE the thermostat sits in the water-inlet housing at the front of the engine, but the gotcha is that an idler pulley hides it -- you have to unbolt and move the idler pulley out of the way before the housing will even come off. Drain the coolant first, pull the lower radiator hose and the belt, get the idler out of the way, then remove the water-inlet nuts to reach the thermostat. It's almost always done during a coolant drain-and-fill or alongside the water pump, and the thermostat coolant crossover pipe with its O-rings is the companion part owners replace at the same time.
Typical difficulty: Moderate — based on 294 code guides for the cooling repair area (an area-level estimate, not this exact job).
Torque specs
Water inlet nuts: verify — Confirm against Toyota factory service info for the 2GR-FE -- do not guess on aluminum.
Tips
The idler pulley blocking the thermostat housing is the single biggest surprise for first-timers -- budget time for it instead of discovering it mid-job.
Install the new thermostat with the jiggle valve facing up (12 o'clock position) per Toyota procedure; a mis-oriented jiggle valve traps air.
P0128 (coolant temp below thermostat regulating temperature) with a temp gauge that never quite reaches the middle is the textbook stuck-open thermostat signature -- a cheap fix to try before anything exotic.
Bleed the cooling system properly afterward -- the 2GR traps air easily and will overheat or gurgle behind the dash if you just pour and go.
Buy the OEM Toyota thermostat; owners report aftermarket thermostats with wrong opening temps causing repeat P0128 codes.
Water pump replacement Owner-verified(3.5L V6 (2GR-FE), 3.5L V6 (2GR-FKS))
The water pump lives on the front of the 2GR-FE behind the serpentine belt drive, and the job is rated medium difficulty -- The Car Care Nut's walkthrough shows it done without pulling the engine and calls it no harder than the spark plugs once you've done those. Access means draining the coolant, pulling the serpentine belt, the idler and tensioner pulleys, and the passenger-side engine mount; the pump comes out the front once those are clear. While you're in there, owners replace the thermostat coolant crossover pipe and its O-ring seals at the same time -- the pump job exposes them anyway and the seals are a known secondary leak point.
Typical difficulty: Moderate — based on 294 code guides for the cooling repair area (an area-level estimate, not this exact job).
Torque specs
Water pump bolts: verify — Confirm against Toyota factory service info for the 2GR-FE before torquing.
Thermostat crossover pipe fasteners: verify — Confirm against factory service info if you do the crossover pipe alongside the pump.
Tips
Owners repeatedly say: use the genuine Toyota water pump (it ships with all the O-rings) -- aftermarket pumps, even Aisin kits, have drawn complaints and failures in owner threads.
The classic symptom is slow coolant loss with no obvious leak -- pink crust or dampness at the pump weep hole under the pulley, sometimes combined with a growling or whining bearing noise. Look under the pulley with a flashlight before assuming head gaskets.
Refill with Toyota pink SLLC coolant and bleed the system properly -- the 2GR is notorious for overheating, no heat at idle, and dash gurgling if air is left in; a spill-free coolant funnel is the owner-favorite tool.
Budget two gallons of coolant and replace the serpentine belt, idler pulley and tensioner pulley while they're off -- they're in your hands already.
Plan on a full day your first time; repeat owners say it gets dramatically faster once you've done one.
The front three plugs are easy; the rear three are buried under the windshield cowl. Owners go at it one of two ways: remove the upper intake plenum (surge tank), which labor guides quote 2.6 hours for on its own, or pull the wiper arms, cowl panel, wiper motor and tray for a tight-fit direct shot at the rear bank. The Car Care Nut method leaves the plenum bracket attached to the plenum and lifts them together. On the 2017-2019 2GR-FKS (direct-injected facelift engine) Toyota simplified the plenum hangers to a single small bracket near the throttle body, so the plenum comes off in about 15 minutes and the whole job can be done in under an hour.
Typical difficulty: Easy — based on 64 code guides for the ignition repair area (an area-level estimate, not this exact job).
Typical time: “Owners go at it one of two ways: remove the upper intake plenum (surge tank), which labor guides quote 2.6 hours for on its own, or pull the wiper arms, cowl panel, wiper motor and tray for a tight-fit direct shot at…” — as written in the note. First-timers often take twice this.
Torque specs
Spark plugs: verify — Confirm against Toyota factory service info for the 2GR-FE/2GR-FKS before torquing -- aluminum heads.
Intake plenum fasteners: verify — Owners stress not over-torquing the plastic plenum on reinstall -- confirm spec in the factory service manual.
Tips
Replace the intake plenum gasket and throttle body gasket while the plenum is off -- owners treat them as one-job consumables, and do the PCV valve at the same time.
Tape or cover the exposed intake runners and throttle body the moment the plenum comes off -- dropped debris into an open runner is the classic self-inflicted wound on this job.
The coil-pack electrical connectors crumble with age on 2014-2016 models; don't push straight down on the release tab, use finesse. On 2017+ models the updated connectors fit extremely tight and releasing them can be the hardest part of the job.
Buy genuine Denso or NGK plugs from a dealer or real parts store -- owners report getting burned by counterfeit plugs and doing the whole job twice.
Toyota's procedure does not call for anti-seize on the plug threads; owners who follow the factory instructions skip it.
Lay a big piece of cardboard under the engine bay and bring a long magnetic pickup tool and a mirror -- you'll drop bolts and sockets behind the plenum.
Rear-bank coils seize in their tubes -- expect a wrestling match; one owner needed a homemade tool to extract a coil boot stuck on a plug.
Removing the cowl is also a good excuse to treat the faded black plastic with a restorer while it's off.
Transmission fluid service Owner-verified(3.5L V6 (2GR-FE), 3.5L V6 (2GR-FKS))
The 2014-2016 models run the U660E 6-speed and the 2017-2019 facelift runs the UA80E 8-speed; both are 'sealed' units with no dipstick -- there's a fill plug on the side of the case and a drain plug with a level-check tube in the pan. Owners do drain-and-fills rather than flushes: drain what's in the pan (roughly 3-4 quarts on the 8-speed, a bit over a quart per drain on some reports), refill the same measured amount through the fill port with a fluid pump, then set the level with the check plug open at the correct ATF temperature window (~104-113F / 40-45C, monitored with an IR gun on the pan or a cheap OBD dongle). The fluid-level tube inside the pan is only hand-tight -- the check-plug procedure is where owners say you can't wing it.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Torque specs
Drain/fill plugs: verify — One popular owner walkthrough cites 36 lb-ft for the fill and drain plugs -- treat as unverified and confirm against the Toyota factory service manual for your transmission before torquing.
Fluid level tube (inside pan): verify — Owner consensus: hand-tight only -- it is not a torqued fastener.
Tips
Use genuine Toyota WS ATF only -- this is the single most repeated rule in owner threads; wrong fluid in a U660E/UA80E is expensive.
Never trust 'lifetime fluid' -- owners doing 60k-100k drain-and-fill intervals report the drained fluid dark but not burnt, and do 2-3 sequential drains spaced ~500 miles apart to work through the fluid gradually.
Do the level check on level ground with the engine running and the ATF in the 104-113F window; too hot or too cold and the set level will be wrong. Shift through every gear for a few seconds each before checking.
Replace the crush washers on the drain and check plugs -- they're one-time-use and leaking WS fluid out of a 'sealed' trans is an expensive mistake.
The transmission fill plug is a 24mm and the drain is a 10mm hex on the 8-speed -- confirm plug sizes against your specific year before buying sockets.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
NHTSA recorded 110 complaints for the 2014–2019 Toyota Highlander. 2016 was the worst year (110 complaints). Most-reported areas: unknown or other, service brakes, electrical system.
18E107000 (27/11/2018) — ELECTRICAL SYSTEM Fujian Wanda Automobile Glass Industry (Wanda) is recalling certain aftermarket Replacement Windshields sold for use in 2014-2018 Toyota Highlander vehicles. The windshields have an attached wire harness that water may leak into, possibly causing damage to the vehicle's Engine Control…
16V775000 (24/10/2016) — ELECTRICAL SYSTEM:WIRING Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2016 Highlander vehicles manufactured May 26, 2016, to September 16, 2016. The brake fluid level sensor may not be connected to the wire harness, preventing the sensor from detecting…
16V420000 (09/06/2016) — EQUIPMENT:OTHER:LABELS Southeast Toyota Distributors, LLC (SET) is recalling certain model year 2016 Toyota Camry and Highlander, 2015-2016 Toyota Tundra, Scion FR-S, and tC vehicles. The Load Carrying Capacity Modification Label may not reflect the correct added weight of the installed accessories…
3 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
NHTSA has published 651 manufacturer communications (service bulletins, dealer notices) covering the 2014–2019 Toyota Highlander.
Most cited systems: Equipment (333), Electrical System (153), Structure (79), Engine (41), Engine And Engine Cooling (36).
Latest bulletins:
T-SB-0055-24 Rev2 (Jan 2026) — Unknown Or Other
T-TT-0790-25 (Aug 2025) — Electrical System
T-SB-0058-23 Rev1 (Jun 2025) — Electrical System
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.