Community-sourced DIY repair guides for the 2024–2024 Toyota Grand Highlander, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Dealer-only recall: the curtain shield airbag assemblies are replaced at the dealer, free of charge. Nothing to DIY here — this is a safety noncompliance, so don't delay.
Torque specs
Curtain shield airbag fasteners: verify — Dealer recall work — fastener torque not published in owner sources; confirm against factory service info.
Tips
NHTSA campaign 24V461000 (Toyota 24TA09/24TB09, Lexus 24LA05/24LB05), June 2024: 145,254 model-year-2024 Grand Highlander, Grand Highlander Hybrid, and Lexus TX vehicles. The driver's-side curtain shield airbag may not unroll as intended when the window is down — part of the bag can end up outside the window opening, failing federal ejection-mitigation rules.
The defect was caught in NHTSA crash testing. Toyota issued a stop-sale and paused production at the Princeton, Indiana plant while engineers redesigned the airbag anchoring system; sales resumed once the fix was in place.
The dealer remedy replaces the curtain shield airbag assemblies with the redesigned parts, free of charge. Until the fix is done, Toyota advised keeping the driver's window closed.
No tools needed: GST mails you a corrected label to stick over the old one. Nothing to buy, nothing to install mechanically.
Torque specs
Label: verify — Adhesive label only — no torque involved.
Tips
NHTSA 24V548000 (Gulf States Toyota 24R2), July 2024: 33,848 vehicles with GST dealer accessories, including the 2024 Grand Highlander and Grand Highlander Hybrid. The load-carrying-capacity modification label can show inaccurate added-weight values, failing FMVSS 110.
Only applies if you bought the vehicle in the Gulf States region (Texas, Oklahoma, Louisiana, Mississippi, Arkansas) with dealer-installed accessories. GST mails corrected labels to owners free of charge.
Front drive shaft clicking on acceleration Factory-documented(2.4L turbo I4 (T24A-FTS), 2.5L I4 hybrid (A25A-FXS))
Drive shaft replacement is a lift job — the axle nut, lower ball joint, and knuckle come apart to free the shaft. Realistic for a well-equipped DIYer, but the dealer's chassis-ear diagnosis is the fast way to confirm which side is clicking before buying parts.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Torque specs
Front axle / hub nut: verify — Axle nut torque not confirmed from an owner source — look it up in factory service info before reassembly; this nut is single-use on most Toyotas.
Tips
T-SB-0082-24 (September 2024): some 2024 Grand Highlanders develop a rotational clicking noise from one or both front drive shaft assemblies when accelerating from low speed, especially while turning. The published fix is replacement of the affected front drive shaft assembly.
The bulletin has the dealer confirm the noise with a chassis ear on the front knuckle, then replace the shaft — and requires a 5-minute grease-distribution drive above 40 mph afterward, or the joint can be damaged and the noise can come back.
Covers both the 2.4T gas model and the 2.5L hybrid; owner complaints on file with NHTSA describe the same low-speed clicking while turning.
MIL on, P05CE00 cold-start camshaft timing Factory-documented(2.4L turbo I4 (T24A-FTS), 2.4L turbo I4 hybrid (T24A-FTS, Hybrid Max))
Dealer-only software update, free under the campaign. If you scan P05CE00 yourself, check for the campaign before paying for any diagnosis.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Torque specs
ECM connectors: verify — Software-only update — no hardware is replaced. No torque involved.
Tips
Toyota Special Service Campaign 24TC05 (September 2024): certain 2024 Grand Highlanders can set a check-engine light with DTC P05CE00 — cold-start 'B' camshaft position timing performance, bank 1. A programming error can let the exhaust variable-valve-timing locking pin stick temporarily.
The campaign covers both the 2.4T gas model (T-SB-0103-23) and the 2.4T Hybrid Max (T-SB-0052-24). Any authorized Toyota dealer updates the engine-control software free of charge; there are no drivability symptoms, just the light and the code.
California note: the state ties this emissions-related campaign to registration renewal — get it done before your smog cycle if you're in California.
Dealer-only reflash with Toyota's GTS+ tool — but knowing the TSB number is the DIY part: it turns a 'could not duplicate' visit into a 40-minute warranty flash.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Torque specs
ECM connectors: verify — No hardware is replaced — the bulletin explicitly says not to replace the ECM. Software only.
Tips
T-SB-0017-24 Rev1 (April 2024): some 2024 Grand Highlander Hybrids (the 2.4T Hybrid Max) hesitate when accelerating from 0–40 mph with steady throttle — a dead-pedal pause that owners describe as the car briefly ignoring the accelerator when pulling into traffic.
The published fix is an ECM/PCM reflash to updated calibration logic (0.7 hr), covered under the federal emissions warranty — 96 months or 80,000 miles.
One owner on record had the reflash done and felt the hesitation return days later with no further fix offered — if yours comes back after the update, push the dealer to re-diagnose rather than accepting 'cannot duplicate.'
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
What owners report
NHTSA recorded 233 complaints for the 2024–2024 Toyota Grand Highlander. 2024 was the worst year (233 complaints). Most-reported areas: unknown or other, power train, engine.
25V744000 (30/10/2025) — BACK OVER PREVENTION:DISPLAY FUNCTION Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2022-2026 Toyota, Lexus, and Subaru Solterra vehicles equipped with a Panoramic View Monitor (PVM) system. Please see the recall report for a complete list of models. A software error may cause…
24V548000 (23/07/2024) — EQUIPMENT:OTHER:LABELS Gulf States Toyota, Inc. (GST) is recalling certain Toyota 2023 GR Supra, 2024 4 Runner, Corolla, Grand Highlander, Grand Highlander Hybrid, Land Cruiser Hybrid, Tacoma, Tacoma Hybrid, 2023-2024 BZ4X, Corolla Cross Hybrid, GR Corolla, GR86, Highlander, Highlander Hybrid, Prius, Prius…
24V461000 (20/06/2024) — AIR BAGS:SIDE/WINDOW:CURTAIN Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2024 Toyota Grand Highlander, Grand Highlander Hybrid, Lexus TX350, TX500 Hybrid, and TX550 Hybrid+ vehicles. The driver and passenger side curtain air bags may not unroll as intended and could partially…
25V595000 (11/09/2025) — ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2023-2024 Toyota Venza, 2023-2025 RAV4 Prime, RAV4, Highlander, GR Corolla, Crown, 2024-2025 Lexus TX, LS, Toyota Tacoma, Grand Highlander, and 2025 Lexus RX, Toyota Crown Signia, Camry, RAV 4 Plug-in Hybrid…
4 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
We don't have factory bulletin data for the 2024–2024 Toyota Grand Highlander yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.