Community-sourced DIY repair guides for the 2015–2019 Subaru Legacy, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Owner-verified repair guides
FB25 oil consumption — test path Owner-verified(2.5L FB25 H4)
Consumption test is dealer-run, but monitoring is owner DIY: check the dipstick every 500-1,000 miles and top off to the full mark. The test itself requires the dealer to fill, seal, and measure the oil over a fixed mileage interval.
Typical difficulty: Moderate — based on 5 code guides for the oil repair area (an area-level estimate, not this exact job).
Torque specs
Drain plug: verify — Owner monitoring only — no forum-confirmed drain plug torque for this job; confirm against factory service info.
Tips
Multiple Legacy-specific threads on legacygt.com report the 2.5L FB25 burning oil — typically about a quart per 1,200-2,000 miles — well past the mileage where the 2011-2014 settlement-era engines were flagged.
The dealer's formal test uses the same bar owners quote from other Subaru models: roughly 1/3 quart or more per 1,200 miles counts as excessive. Ask the dealer to start a documented oil-consumption test if yours is near or past that rate.
Key Legacy detail: the Legacy was NOT included in the FB25 class-action settlement (that covered Forester, Outback, Impreza, and Crosstrek). There is no extended warranty on Legacy consumption — your only factory path is to fail the dealer's consumption test inside the standard powertrain warranty, where the documented remedy is ring or short-block work.
Do not wait for the low-oil light: by the time it triggers, owners report the crankcase can be more than a quart low. Check the dipstick at every other fuel fill-up and carry a quart of the specified 0W-20.
If the dealer test passes but consumption continues, keep records: dated dipstick readings and receipts for added oil are what owners say eventually convinced service managers to escalate.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
What owners report
NHTSA recorded 147 complaints for the 2015–2019 Subaru Legacy. 2016 was the worst year (147 complaints). Most-reported areas: electrical system, unknown or other, visibility/wiper.
15V794000 (24/11/2015) — POWER TRAIN:DRIVELINE:DRIVESHAFT Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing…
16V292000 (11/05/2016) — STEERING:COLUMN Subaru of America, Inc. (Subaru) is recalling certain model year 2016-2017 Legacy and Outback vehicles manufactured February 29, 2016, to May 6, 2016. The steering column on the affected vehicles may have been improperly machined, and as a result, turning…
15V502000 (10/08/2015) — POWER TRAIN:DRIVELINE:DRIVESHAFT Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft…
3 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
We don't have factory bulletin data for the 2015–2019 Subaru Legacy yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.