Community-sourced DIY repair guides for the 2013–2020 Subaru BRZ, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Chirping or squealing from the bellhousing at idle that stops when you press the clutch pedal slightly points at the clutch fork pivot or the throwout bearing; noise that appears only with the pedal fully depressed points at the bearing itself under load. Either way the transmission has to come out, so budget the job as a clutch replacement and do the bearing, fork, and pivot together.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Sources: FT86Club 'Throwout bearing.' — owner discussion: the TOB spins constantly with the engine running, noise diagnosis · FT86Club 'Full list of what I need for clutch/TOB replacement install?' — revised TOB part, fork, pivot, retainer checklist · FT86Club 'DIY Clutch Replacement' — step-by-step 86/BRZ clutch and release-bearing replacement walkthrough
No owner reports yet — fixed this yourself? tell us how
A check-engine light for P0351-P0354 (ignition coil primary circuit) that shows up at high RPM under load — owners report it striking around 5,300 rpm at full throttle — is the classic FA20 coil-pack failure. Confirm by swapping the suspect coil to another cylinder: if the code follows the coil, the coil is bad. Subaru released updated coils and a revised harness (TSB 07-120-17R) for 2013-2014 cars.
Typical difficulty: Easy — based on 64 code guides for the ignition repair area (an area-level estimate, not this exact job).
Sources: FT86Club 'CEL P0351 Ignition Coil A Primary Control Circuit/Open' mega-thread — owner swap-test procedure and 20-minute passenger-side replacement · FT86Club 'P0351 bad spark plug...' — coil failure progression and plug-well access notes (14mm plugs, jack the engine for access)
p0351 on this Subaru BRZ — full diagnosis guide →
No owner reports yet — fixed this yourself? tell us how
Condensation inside the taillights after rain or a car wash means the thin foam gasket between the lamp assembly and the body has failed — not the lamp itself. Pull the assembly (four 10mm nuts per side), dry it out, and re-seal with a rebuilt gasket plus silicone sealant on both sides.
Sources: FT86Club 'Tail Light Condensation' mega-thread — gasket failure diagnosis and silicone re-seal procedure that held through wet seasons · FT86Club 'DIY Tail Light Gasket' — build a permanent 1/4-inch neoprene replacement gasket · FT86Club 'BRAINDUMP - FT86 Quirks, common fixes' — taillight gasket listed among the platform's known quirks with the easy fix
No owner reports yet — fixed this yourself? tell us how
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
NHTSA recorded 5 complaints for the 2013–2020 Subaru BRZ. 2016 was the worst year (3 complaints). Most-reported areas: suspension, wheels, service brakes.
Counts are NHTSA complaints filed for these model years, via the NHTSA API. See data for all BRZ years →
We don't have factory bulletin data for the 2013–2020 Subaru BRZ yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.