2013–2013 Subaru BRZ

Community-sourced DIY repair guides for the 2013–2013 Subaru BRZ, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.

Owner-verified repair guides

Valve spring recall (18V-772): free dealer fix, but verify the work afterward Factory-documented (2.0L FA20 flat-4)

Dealer recall, free at any Subaru or Toyota dealer — but confirm it was actually done before you buy a 2013. NHTSA 18V-772 covers 2013 BRZ and Scion FR-S cars whose valve springs can fracture and stall the engine without warning. Check the VIN at nhtsa.gov/recalls. Owner-reported catch: FT86Club tracked dozens of engine failures shortly AFTER the recall repair, with excess liquid gasket from reassembly suspected of blocking oil passages — if the recall was just done, change the oil early and cut the filter open to look for sealant debris.

Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).

Torque specs

Tips

Sources: NHTSA recall 18V772000 — engine valve springs may fracture, dealers replace free (NHTSA API) · TheDrive: FR-S went up in flames two weeks after the valve spring recall; FT86Club registry of post-recall failures · FT86Club 'Valve spring repair dealer hub' — owner thread on dealer upsells during the recall (clutch, plugs, induction service)

No owner reports yet — fixed this yourself? tell us how

Idle dip and stalling on early cars: ECU reflash fixes it, not parts Owner-verified (2.0L FA20 flat-4)

The earliest 2013 cars can suffer a rough, dipping idle or outright stalling — sometimes with a check-engine light — caused by ECU mapping with tolerances set too tight from the factory, not by bad parts. The fix is a dealer ECU reflash to a newer calibration. Check which calibration ID your ECU is running before buying sensors.

Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).

Torque specs

Tips

Sources: Jalopnik: 'Here's How To Fix The Scion FR-S And Subaru BRZ Engine's Idle Problem' — dealer reflash confirmed as the fix · FT86Club 'Idle dip' thread — calibration ID history (ZA1J700C through ZA1JD00C) and TSB-backed updates · Autoblog: FR-S/BRZ rough idle requires ECU reflash; Subaru says reflash suffices at any mileage

p0019 on this Subaru BRZ — full diagnosis guide →

No owner reports yet — fixed this yourself? tell us how

Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

Codes on this BRZ

P0019
2013–2013 Subaru BRZ
Idle dip and stalling on early cars: ECU reflash fixes it, not parts

What owners report

No NHTSA complaint data in our records for the 2013–2013 Subaru BRZ specifically. See NHTSA data for all BRZ years →

Factory service bulletins

We don't have factory bulletin data for the 2013–2013 Subaru BRZ yet.

Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.

Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.