Community-sourced DIY repair guides for the 2019–2026 Ram 2500, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Owner-verified repair guides
6.7L hydraulic roller lifter failure — tick to cam wipe to engine death Owner-verified(6.7L Cummins Turbo Diesel)
Listening job — pop the hood, set the high idle and listen from each side. The failure announces itself long before it kills the engine; catching the tick while it is still intermittent is the difference between a lifter job and a new engine.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Tips
In 2019 the 5th-gen 6.7L Cummins switched from solid flat tappets to hydraulic roller lifters to kill the valve-lash adjustment and quiet the engine. It introduced a new failure point: the roller at the end of each lifter has NO needle bearings, and a dowel pin keeps the lifter aligned in the bore — a misaligned lifter eats the cam (SlashGear).
The kill chain: the roller stops rolling and starts dragging on the cam lobe, grinding the lobe flat and pumping metal shavings through the entire engine. Failures have struck within the first 10,000 miles as well as past 100,000 (diesel conversion shop field data).
Owner-reported progression (Cummins Forum): a typewriter-like tick on startup, worse in cold weather when oil is thick — intermittent at first, then persistent, then louder, then weird running issues, then engine codes, exhaust smoke, and power loss.
Do NOT assume a silent valvetrain is healthy. One owner drove with a bent pushrod for at least 30,000 miles — no tick, no rattle — because the collapsed lifter pumped up just enough to stay quiet until it wedged itself in the block. Modified owners only catch bent pushrods when the top end is apart (Cummins Forum).
This is a different campaign from the gas 6.4L HEMI MDS lifter failures and from the grid-heater bolt / CP4 issues — Cummins hydraulic rollers only, 2019 model year and newer.
10W-30 vs 15W-40: the July 2023 oil bulletin (TSB 09-013-23) Factory-documented(6.7L Cummins Turbo Diesel)
Driveway job — nothing to disassemble. This is a buy-the-right-jug job: check the owner's manual spec sticker and pour 10W-30 CK-4 (or 5W-40 full synthetic in sustained below-0°F cold). The mistake is using the old 15W-40 habit on a 2019+ truck.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Tips
Stellantis TSB 09-013-23 (July 12, 2023, rev of 09-011-20) is the factory's only official action on the lifter problem: 2019 model year and newer 6.7L trucks MUST use 10W-30 engine oil meeting FCA MS-10902 / API CK-4 (Cummins CES 20081 also accepted); 2018 and older stay on 15W-40 CJ-4. Below 0°F sustained, 5W-40 full synthetic is required for all years.
The bulletin's CAUTION, verbatim: '15W-40 grade oil CAN NOT be used in any 2019 model year or newer 6.7L equipped vehicles due to the new designed valve train of this engine. If this oil is used, it will cause deposits to form in the Hydraulic Valve Lash Adjusters leading to undesirable noise, and/or engine damage.'
What owners BELIEVE (BobIsTheOilGuy debate): many say Ram published findings with no proof — viscosity alone can't form deposits; the real cause is a bad batch or the design itself; trucks running 15W-40 for years with zero issues prove it. What is PROVEN: only the TSB itself. Honest read: correct oil lowers risk per Stellantis's post-mortem data, but even the explainer press says it reduces the chances with no guarantee of eliminating the problem.
Practical upshot from owners: don't run 15W-40 in a 2019+ (it gives the dealer a reason to fight your warranty claim), change it well before the oil-life monitor lets it ride, and don't expect the right oil to save a bad lifter.
Repair-cost math: cam+lifter job vs long block vs new engine Owner-verified(6.7L Cummins Turbo Diesel)
Shop job — the lifters sit under the cylinder heads, so this is engine-out or cab-off territory. Owner-accessible part of this note is the wallet math: know the escalation ladder before you authorize a repair.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Tips
The escalation ladder: (1) camshaft + full lifter set with the engine in the truck — dealers often skip this and jump to (2) a partial engine / long block; (3) complete engine replacement. A diesel conversion shop that does these jobs frames the stakes as 'before your factory lifters cost you a $25,000+ engine' (Pro Automotive & Diesel).
Caught early (tick, cam still good): cam + lifters, engine-out/cab-lift labor. Caught late (metal through the engine): the long block, because debris destroys bearings, the oil pump, and cylinder walls — at that point a cam-and-lifters-only repair is a false economy.
Warranty covers the job inside 5 years / 100,000 miles, but dealers replace the failed parts with the same hydraulic roller design. One 2021 Ram 2500 owner documented the dealership replacing camshaft and lifters TWICE — then failing a THIRD time, sending metal through the oiling system and damaging the crankshaft bearings (CarComplaints).
Expect downtime measured in weeks to months, not days: hydraulic lifter/cam parts have been backordered, and warranty work pays the dealer less, so it sits (Cummins Forum owners report loaner trucks for 7 months in one case).
DIY diagnostic sequence before condemning the engine Owner-verified(6.7L Cummins Turbo Diesel)
Driveway diagnostic job — no special tools beyond a stethoscope, an oil-analysis kit, and patience. Do this sequence before you let anyone condemn the engine.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Tips
Step 1 — the high-idle listen test: owners say the tick is clearest at high idle; one owner pins it louder on the passenger side. Step 2 — document the progression: intermittent at first, then persistent, then louder, then running issues. That timeline is your evidence.
Step 3 — oil analysis: send a Blackstone (or the cheaper Cummins oil-test kit, ~$13–$16) sample and trend copper and iron across changes. One owner's report showed high copper and iron while the truck was still 'fine' — copper/iron trend UP is the early-warning signal.
Step 4 — cut open the oil filter and look for glitter/metal. Step 5 — pull the valve covers, visually inspect pushrods, and check run-out with a dial gauge: modified owners are the ones catching bent pushrods because dealers won't look unless something failed.
Know the dealer's game: multiple owners report dealers refusing to act on the 'typical 2019+ tick' until the lifter has actually failed — build your paper trail (videos, UOA reports) while still under the 5yr/100k powertrain warranty. And remember: 2019+ trucks have NO valve-lash adjustment — it's all hydraulic rollers, so 'adjust the valves' is not a fix.
Coverage context: no recall — warranty-only, 2019+ all years affected Owner-verified(6.7L Cummins Turbo Diesel)
Phone-and-paperwork job — check your VIN against recalls yourself (NHTSA), know your warranty date/mileage, and never assume a 'campaign' exists for this failure.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Tips
The honest coverage finding: as of October 2026 there is NO NHTSA safety recall for the Cummins hydraulic lifter failure. The recalls you will find — CP4 fuel pump (Y78 / 21V-880) and the 67A emissions calibration — are different campaigns with different failure modes. The factory's only official lifter-related action is the TSB 09-013-23 oil-viscosity bulletin.
Affected vs covered: field failures are documented across the full 2019–2026 range (conversion shops list 2019–2024 Ram 2500/3500 as at-risk, owners report 2022s as a hotspot, and 2025 trucks have failed too). Covered = inside the 5-year/100,000-mile diesel powertrain warranty, period.
Warranty repairs replace failed lifters and cam with the SAME hydraulic roller design — not an updated part — which is why repeat failures exist: a 2021 Ram 2500 owner had cam+lifters replaced twice under warranty, then failed a third time with crank-bearing damage.
Out-of-warranty owners carry the whole bill, which is why the cost math (cam+lifter vs long block vs new engine) and the solid-lifter conversion notes exist — decide your plan BEFORE the tick starts.
Solid-lifter conversions: the permanent aftermarket answer Owner-verified(6.7L Cummins Turbo Diesel)
Shop job — cab-off is the practical route for a cam swap in the truck; the magnetic cam-removal tool is what makes an in-chassis install possible. This is not a weekend driveway job.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Tips
The only permanent fix per owners and diesel shops is removing the failure-prone parts entirely: convert back to the solid flat-tappet valvetrain philosophy that made the Cummins legendary. The shops' line: the 10W-30 TSB lowers the risk, it does not remove the design flaw.
Kit math: Wagler's 6.7 lifter conversion/spacer kit runs $1,400+ (new pushrods, adjustable rockers, lifter spacers); Hamilton Cams' kit is about twice that and adds a forged camshaft, tappets, pushrods, and rocker arms. The DNR Customs magnetic cam-removal kit ($499) is what lets either kit go in without pulling the engine.
Owner practice: doing the conversion preemptively or at the first failure instead of accepting another set of factory hydraulic rollers. Several Cummins Forum owners state flatly they will 'just put solid/flat tappets in' rather than reinstall a known weak part.
Watch the warranty: a conversion voids the factory powertrain warranty on the valvetrain — this is an out-of-warranty or post-warranty math decision, not a warranty-claim strategy.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
What owners report
NHTSA recorded 162 complaints for the 2019–2026 Ram 2500. 2020 was the worst year (162 complaints). Most-reported areas: fuel/propulsion system, engine, fuel system.
23V799000 (28/11/2023) — STEERING:STEERING CONTROL MODULE Chrysler (FCA US, LLC) is recalling certain 2023 Ram 1500 Classic, Ram 3500 Classic, 3500 Cab Chassis, 2023-2024 Ram 2500, 4500/5500 Cab Chassis, and Ram 3500 vehicles. The steering column control module may cause the high beams to activate when…
23V654000 (28/09/2023) — BACK OVER PREVENTION:DISPLAY FUNCTION Chrysler (FCA US, LLC) is recalling certain 2022-2023 Ram 1500, Ram 3500 Cab Chassis with GVWR less than 10,000 lbs., and 2022-2024 Ram 2500 vehicles. The radio software may prevent the rearview image from displaying. As such, these vehicles fail…
22V035000 (27/01/2022) — VISIBILITY:WINDSHIELD WIPER/WASHER:LINKAGES Chrysler (FCA US, LLC) is recalling certain 2019-2020 Ram 2500 and Ram 3500 vehicles, Ram 3500 Cab Chassis, 4500 Cab Chassis, 5500 Cab Chassis and 3500 Cab Chassis with a gross vehicle weight rating (GVWR) of less than 10,000 lbs…
20V043000 (24/01/2020) — POWER TRAIN:AUTOMATIC TRANSMISSION Chrysler (FCA US LLC) is recalling certain 2019-2020 Ram 2500 and 3500 Pickup vehicles equipped with six-speed automatic (68RFE) transmissions. A build up of pressure and heat inside the transmission may result in a transmission fluid leak from the dipstick…
26V327000 (21/05/2026) — BACK OVER PREVENTION: SENSING SYSTEM: CAMERA Chrysler (FCA US, LLC) is recalling certain 2019 and 2023 Chrysler Pacifica, 2024 Ram 1500, Ram 2500, and 2024-2025 Jeep Wrangler vehicles. Contamination in the central vision processing module or improper programming may cause the rearview camera image not to…
25V010000 (16/01/2025) — AIR BAGS:SIDE/WINDOW:CURTAIN:INFLATOR Chrysler (FCA US, LLC) is recalling certain 2016-2019 Ram 3500, Ram 1500, 2016-2020 Ram 2500, and 2016 Ram 3500 Cab Chassis vehicles. The right and left side curtain air bag inflators may rupture due to a manufacturing defect.
15 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
We don't have factory bulletin data for the 2019–2026 Ram 2500 yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.