Community-sourced DIY repair guides for the 2014–2024 Ram 2500, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Shop job — cam and lifter replacement is an engine-teardown task. Pinpointing the tick source and choosing the MDS-delete route vs stock parts is the DIY decision point.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Torque specs
Cam / valvetrain fasteners: verify — Torque spec not confirmed from a forum source — confirm against factory service info for your year before reassembly.
Tips
Yes — the 6.4 HEMI suffers the same MDS lifter failure pattern as the 5.7: the cylinder-deactivation lifters collapse and wear the cam lobes. Owners report a loud ticking/tapping at idle that tracks with engine speed.
Once the tick starts, it is a cam-and-lifter replacement, not an additive fix. One 2018 2500 owner did an MDS delete — non-MDS cam with Hellcat non-MDS lifters — for roughly $1,500 in parts and under $3,000 in shop labor.
The MDS-delete route is popular because the failure can repeat with stock MDS hardware. If the truck is a keeper, price the delete against stock replacement before authorizing work.
Rule out the simpler ticks first: low oil and broken exhaust-manifold bolts both tick. A mechanic's stethoscope on the valve cover (valvetrain tick) versus the exhaust manifold (manifold-bolt tick) tells you which one you have.
Get the exact failed bank and parts list in writing before approving a teardown — dealer quotes for this job vary widely, and 'cam and lifters' can mean one bank or both.
Work through the front wheel wells with the truck on jack stands, wheels off, and the engine stone cold. The manifold heat shields come off first; every bolt you touch gets a PB-Blaster soak before you touch it. The driver side is the hard one - the steering column and dipstick tube are in the way.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Torque specs
Exhaust manifold bolts (to head): verify — Owner-reported 18 ft-lb on 5.7L HEMI trucks; confirm against factory service info for the 6.4L. Center-out sequence; re-check after one full heat cycle.
Tips
Confirm it is bolts before you wrench: the cold-start tick that fades as the engine warms is the classic broken-manifold-bolt exhaust leak. The rearmost bolts break first, usually on the driver side. Grab the heat shield corners through the wheel well with the engine cold - a loose or rattling shield means broken bolts underneath. (The separate MDS lifter note covers the lifter tick, which does NOT fade with warmth.)
The root cause is the manifold, not the bolts: the factory cast-iron manifolds warp from heat cycles - worse on trucks that tow, where exhaust gas temperatures run high - and the warping stretches and snaps the M8 bolts. The bolts themselves are 10.9 grade; it is the manifold distorting that kills them.
Do not bolt a warped manifold back on or you will snap the next set of bolts. Check each manifold for flatness; owners either machine-shop them or replace them. The BD Diesel kit (1041454, built specifically for 2014-2024 Ram 2500-5500 6.4L) uses high-silicon ductile iron that resists warping, plus longer bolts with spacers so the manifold can expand and contract without binding.
Extraction is the whole job: if the stud snapped above flush, Vise-Grips may walk it out; if it is flush or below, welding a nut onto the stub is the community's go-to. The ProMaxx 'Chad' PMXCD200PRO kit is the purpose-built tool for drilling out broken 6.4L HEMI manifold bolts with the head still on the truck.
Reassemble center-out, then do a full heat cycle and re-check torque - owners find bolts loosen after the first heat cycle. On 2019+ trucks Ram added manifold braces and stainless rear bolts, but owners report the issue persists, so do not assume the newer trucks are immune.
6.4L HEMI coolant leak under the intake (heater/coolant hoses) Owner-verified(6.4L HEMI V8)
The leak hides under the intake, so this is an intake-manifold-removal job: expect to pull the intake (and the alternator, per owner reports) just to reach two rubber hoses. Pressure-test the system cold first so you are not guessing.
Typical difficulty: Moderate — based on 294 code guides for the cooling repair area (an area-level estimate, not this exact job).
Torque specs
Intake manifold bolts: verify — Plastic intake with O-ring seals — follow the factory sequence and inch-pound spec; overtightening cracks the manifold.
Hose clamps (under-intake lines): verify — Re-check every clamp before the intake goes back on; a missed clamp means doing the whole job twice.
Tips
The 6.4L HEMI in the 2500 runs coolant plumbing under the intake manifold — a tube/hose run off the water pump area that is prone to fail and leak. When it goes, you get the classic mystery-coolant-loss pattern: disappearing coolant, a sweet smell, maybe wetness at the back of the engine, and nothing visibly leaking up top.
One owner's video shows the job plainly: the intake manifold (and the alternator) had to come off just to replace two rubber hoses buried in the middle of the engine — and it was his second time doing it at only 140,000 miles. Budget the intake gaskets and the hoses together.
While you are in there, check the other under-intake leak points owners flag: the EGR cooler lines with their clamps (prone to leak on the 6.4), and the condition of the coolant tank and cap — one owner reports the tank builds up gunk that cannot be flushed out and a failed cap popped his radiator.
Confirm before you tear down: rent a cooling-system pressure tester and pressurize the system cold — it will show exactly where the coolant is escaping. This is a different campaign from the T51 diesel water-pump recall, which is a separate note.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
What owners report
NHTSA recorded 420 complaints for the 2014–2024 Ram 2500. 2016 was the worst year (258 complaints). Most-reported areas: engine, power train, electrical system.
23V799000 (28/11/2023) — STEERING:STEERING CONTROL MODULE Chrysler (FCA US, LLC) is recalling certain 2023 Ram 1500 Classic, Ram 3500 Classic, 3500 Cab Chassis, 2023-2024 Ram 2500, 4500/5500 Cab Chassis, and Ram 3500 vehicles. The steering column control module may cause the high beams to activate when…
23V654000 (28/09/2023) — BACK OVER PREVENTION:DISPLAY FUNCTION Chrysler (FCA US, LLC) is recalling certain 2022-2023 Ram 1500, Ram 3500 Cab Chassis with GVWR less than 10,000 lbs., and 2022-2024 Ram 2500 vehicles. The radio software may prevent the rearview image from displaying. As such, these vehicles fail…
18V486000 (27/07/2018) — STRUCTURE:BODY:TAILGATE Chrysler (FCA US LLC) is recalling certain 2015-2017 RAM 1500, 2500, and 3500 pickup trucks equipped with a power locking tailgate and either a 5 foot, 7 inch or 6 foot, 4 inch bed. The tailgate actuator limiter tab may…
22V035000 (27/01/2022) — VISIBILITY:WINDSHIELD WIPER/WASHER:LINKAGES Chrysler (FCA US, LLC) is recalling certain 2019-2020 Ram 2500 and Ram 3500 vehicles, Ram 3500 Cab Chassis, 4500 Cab Chassis, 5500 Cab Chassis and 3500 Cab Chassis with a gross vehicle weight rating (GVWR) of less than 10,000 lbs…
19V021000 (25/01/2019) — STEERING:LINKAGES:DRAG:LINK:CONNECTION Chrysler (FCA US LLC) is recalling certain 2013-2018 Ram 3500 and 2014-2018 Ram 3500 Chassis Cab and Ram 2500 vehicles. The outboard steering linkage jam nut may loosen, allowing one end of the drag link to separate.
20V043000 (24/01/2020) — POWER TRAIN:AUTOMATIC TRANSMISSION Chrysler (FCA US LLC) is recalling certain 2019-2020 Ram 2500 and 3500 Pickup vehicles equipped with six-speed automatic (68RFE) transmissions. A build up of pressure and heat inside the transmission may result in a transmission fluid leak from the dipstick…
28 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
We don't have factory bulletin data for the 2014–2024 Ram 2500 yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.