Community-sourced DIY repair guides for the 2013–2018 Ram 1500, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Owner-verified repair guides
8HP70 transmission service (pan/filter, not flush) Owner-verified(5.7L HEMI V8, 3.6L Pentastar V6)
Pan drop from below — the filter is built into the plastic transmission pan, so a service means a whole new pan. Fill through the side fill plug; there is no dipstick. The truck must be level (rear raised 8-9 inches on ramps) and the fill completed before fluid temp passes 122F.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Torque specs
8HP70 pan bolts: verify — Pan bolt torque not confirmed from a forum source — confirm against factory service info. The plastic pan gasket is single-use with the pan.
Tips
Settle the 'lifetime fluid' debate with the source that matters: ZF — the company that designed the 8HP70 — recommends fluid and filter every 60,000-80,000 miles (50k if you tow). Ram's 'lifetime' means the life of the warranty, not the life of your truck. Owners keeping trucks past 100k service it.
Pan drop ONLY — never a pressurized flush on a high-mileage, never-serviced unit. Multiple owners and techs warn a flush can dislodge debris into worn clutches and create problems you didn't have; the pan drop with a new filter is the safe, manufacturer-blessed procedure.
Budget for the pan, not just fluid: the filter is molded into the plastic OE pan, so the pan is a one-use item (roughly $228 from Mopar parts). The PPE aluminum pan with a replaceable filter costs about the same and makes the NEXT service cheaper — the popular owner upgrade.
Fluid spec is Mopar 8 & 9 Speed ATF (68218925AA), which is ZF Lifeguard 8 — about 8.77 quarts total capacity. Valvoline MaxLife labeled compatible with ZF 8-speed is the commonly used alternative. Use the wrong fluid and the 8-speed will let you know.
The level-setting procedure is the fiddly part: truck level (rear up 8-9 inches), engine running, fill until fluid overflows the side plug, all before fluid temp exceeds 122F. Working under a running truck is unavoidable — plan the setup, wear protection, and don't rush the temp window.
4-corner air suspension leaks and compressor failure Owner-verified(5.7L HEMI V8, 3.6L Pentastar V6, 3.0L EcoDiesel V6)
Leak-check from the driveway with a spray bottle of soapy water; the boots pull down after cutting the zip tie. Compressor work is under the bed at the passenger-rear corner. Put the system in Tire Jack Mode on the dash BEFORE disconnecting the battery.
Typical difficulty: Moderate — based on 27 code guides for the suspension repair area (an area-level estimate, not this exact job).
Torque specs
Compressor mounting fasteners: verify — No published owner torque figure for the compressor or valve block - hand-tighten to service-info spec and leak-check every fitting with soapy water before refilling with nitrogen.
Tips
Know the failure pattern: one end sags overnight and airs back up on start = a slow leak (bag, fitting, or valve block). The whole truck drops and stays on the bump stops with a Christmas tree of warnings ('Immediate Air Suspension Service Needed', service trailer brake, traction disabled) = the compressor gave up chasing the leak.
Find the leak with soapy water before buying parts. Pull the protective boots down (cut the zip tie), spray the bellows and fittings - bubbles grow obviously, 'you will not miss it'. The lines from the valve block to the bags are one piece with no junctions, so focus on the bags themselves and the fittings.
The compressor is rebuildable, and that's the money tip. It's an industry-standard Continental unit shared with the Grand Cherokee, Tesla Model S, and Volvo XC90 - a rebuild kit for a 2014 Grand Cherokee fits the Ram compressor perfectly, and one owner did new bags, valve block, and a compressor rebuild for $525 all-in versus a $4,000-5,000 dealer quote with the compressor backordered.
Rebuild details from an owner who did it: release the 4 bolts at the same time (there's pressure inside, keep the end section straight so you don't damage the big O-ring), make sure the connecting rod goes onto its shaft, and reuse the OEM gaskets. New cylinder and piston, take your time.
After any repair the system needs a vacuum pull and a nitrogen refill - the system is nitrogen-filled to fight moisture. Owners get a nitrogen tank at a welding supply store and borrow a vacuum pump (AutoZone's loan-a-tool). A scan tool that talks to the suspension module (AlfaOBD with an OBDLink MX+ is the forum standard) clears codes and exits 'In Plant Mode' to get out of limp-home.
A hot compressor is a dying compressor: one owner felt 80C on a freezing day ('calculated temperature' in AlfaOBD) with a 'compressor overheating / wait, air suspension cooling down' message - that compressor was running constantly against a leak. Fix the leak first, then the compressor.
The housing sits in the intake valley under the engine cover, so the flashlight test is free. The replacement requires pulling the intake manifold - a solid afternoon job, not a quick filter swap.
Typical difficulty: Moderate — based on 5 code guides for the oil repair area (an area-level estimate, not this exact job).
Torque specs
Oil filter housing bolts: verify — E8 inverted Torx per the video guides; torque to service-info spec - the housing is plastic on OEM units and cracks from over-tightening.
Oil filter cap: verify — Inch-pound territory. Owner practice ranges from a 1/4-inch torque wrench to single-finger snug with the smallest ratchet.
Tips
The free diagnosis: pull the engine cover and shine a flashlight down into the intake valley by the filter housing. If the valley is full of oil, the housing or its lower seals are the source - the oil then runs down the back of the engine and soaks the bell housing, which looks like a rear main seal leak but isn't.
This housing leaks oil AND coolant - the oil cooler is integrated into the same plastic assembly. Owners report the smell of burning oil for years before it ever drips on the driveway, and sudden cracks (often right after an oil change) can dump a lot of oil fast.
The community fix is the all-aluminum upgraded housing (Dorman's OE FIX is the one owners name) instead of another plastic OEM unit - the plastic warps and cracks from heat cycling in the valley, and the updated OEM part is still mostly plastic. The aluminum unit comes with the gaskets and seals for the intake manifold.
Watch the filter cap: owners agree the housing cracks from over-tightening. One 3.6 owner uses a 1/4-inch torque wrench at inch-pound spec and says it clicks almost instantly; the next guy just goes finger-snug with his smallest ratchet. Either way, don't gorilla it.
Model-year gotchas from the video guides: 2011-2013 used the old filter part number (a new housing updates you to the 2014+ filter), and 2017+ trucks need the upper sensor swapped from the old housing onto the new one. Confirm which sensors your housing has before you button the intake back up.
While the intake is off for the housing, owners suggest budgeting the coolant refill carefully - bleeding the cooling system is the fiddly part of the job; a vacuum filler makes it far easier.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
What owners report
NHTSA recorded 1,544 complaints for the 2013–2018 Ram 1500. 2016 was the worst year (1544 complaints). Most-reported areas: steering, engine, service brakes.
18V486000 (27/07/2018) — STRUCTURE:BODY:TAILGATE Chrysler (FCA US LLC) is recalling certain 2015-2017 RAM 1500, 2500, and 3500 pickup trucks equipped with a power locking tailgate and either a 5 foot, 7 inch or 6 foot, 4 inch bed. The tailgate actuator limiter tab may…
19V757000 (24/10/2019) — ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE) Chrysler (FCA US LLC) is recalling certain 2014-2019 Ram 1500 and 1500 Classic Pickup trucks equipped with 3.0L Eco Diesel engines. The Exhaust Gas Recirculation (EGR) cooler may crack and allow pre-heated vaporized coolant to enter the EGR system. This…
17V198000 (23/03/2017) — POWER TRAIN:DRIVELINE:DIFFERENTIAL UNIT Chrysler (FCA US LLC) is recalling certain 2016-2017 Ram 1500 trucks. The differential pin retaining screw may come loose while driving, potentially causing the differential to break or lock up.
16V167000 (23/03/2016) — STEERING:ELECTRIC POWER ASSIST SYSTEM Chrysler (FCA US LLC) is recalling certain model year 2015-2016 Ram 1500 trucks manufactured January 22, 2015, to September 13, 2015. Contamination on the Electric Power Steering (EPS) control circuit board may cause a short and result in the loss…
17V821000 (20/12/2017) — POWER TRAIN:AUTOMATIC TRANSMISSION:LEVER AND LINKAGE:COLUMN SHIFT Chrysler (FCA US LLC) is recalling certain 2016-2017 Ram 3500 Cab Chassis with a Gross Vehicle Weight Rating (GVWR) of less than 10,000 lbs, 2011-2017 Ram 3500, 4500 and 5500 Cab Chassis vehicles, 2009-2017 Ram 1500 and 2010-2017 Ram 2500…
18V332000 (17/05/2018) — ELECTRICAL SYSTEM:WIRING Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500…
17 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
We don't have factory bulletin data for the 2013–2018 Ram 1500 yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.