Community-sourced DIY repair guides for the 2017–2018 Peterbilt 579, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Owner-verified repair guides
Dash ABS lamp may not warn when ABS controller loses power (18V-368 / PACCAR 18PBB, 18KWD) Factory-documented(12.9L PACCAR MX-13 diesel (405–510 hp), Cummins ISX15/X15 diesel (400–605 hp))
Dealer-only recall repair — free at any Peterbilt dealer. Owner-side value: the predecessor to the giant 20V199 campaign — same silent-ABS failure, smaller population. Both campaigns' notes belong on the truck's record.
Typical difficulty: Moderate — based on 265 code guides for the brake repair area (an area-level estimate, not this exact job).
Torque specs
No owner-serviceable fasteners: verify — Dealer-only recall — NAMUX software update in the cab control module; no owner torque specs apply.
Tips
85,626 trucks (2017-2018 Peterbilt 567 and 579; 2015-2018 Kenworth T660, T680, T800, T880, W900): if the ABS controller loses battery and/or ignition power, the dash ABS warning lamp may not illuminate — the driver gets no warning that ABS is offline. FMVSS 121/136 noncompliance.
This is the campaign that grew into 20V199: PACCAR's follow-up investigation found the original remedy and population inadequate, so 20V199 superseded it with a broader NAMUX software fix. A 2017-2018 579 may legitimately carry both campaign numbers on its history.
Remedy: dealers update the NAMUX software in the cab control module, free. Interim notices mailed July 30, 2018 (PACCAR 18PBB / 18KWD).
Same owner habit as 20V199: verify the ABS lamp lights during key-on self-test. No lamp at self-test means the warning circuit — not the brakes — is the suspect.
Transmission gear display may read N when the shifter is in D or R — FMVSS 101/102 (18V-092 / PACCAR 18KWA, 118-A) Factory-documented(12.9L PACCAR MX-13 diesel (405–510 hp), Cummins ISX15/X15 diesel (400–605 hp))
Dealer-only recall repair — free at any Peterbilt dealer. Owner-side value: the dash says N, the stalk says D, the truck doesn't move — on 2017-2018 579s with Eaton automated transmissions and the stalk shifter, the display lies.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Torque specs
No owner-serviceable fasteners: verify — Dealer-only recall — transmission software update; no owner torque specs apply.
Tips
1,938 trucks (2017-2018 Kenworth T680, T880; Peterbilt 567, 579 — all with Eaton UltraShift Plus or Eaton Advantage automated transmissions and the right-hand stalk shifter): the gear display may indicate 'N' when the shifter is actually in 'D' or 'R' — and the truck will not move. FMVSS 101/102 noncompliance.
Remedy: dealers install a transmission software update, free. The recall began March 9, 2018 (PACCAR 18KWA / 118-A).
For the 579 the range is 2017-2018. Distinguish from 24V190 (2021-2024, stalk CONNECTOR crimping): same shifter location, different failure — display logic vs. wiring. A no-move with a lying display is this campaign; a no-move with a dead stalk is the other.
Cummins ISX fuel pump drive gear may slip on its shaft — engine stall (17V-443 / PACCAR C1909) Factory-documented(Cummins ISX15/X15 diesel (400–605 hp))
Dealer-only recall repair — free at any Peterbilt dealer. Owner-side value: the fuel pump's drive gear slips on its shaft and the pump quits — on 2017-2018 Cummins ISX 579s, a sudden stall with fuel in the tanks points here.
Typical difficulty: Moderate — based on 483 code guides for the fuel repair area (an area-level estimate, not this exact job).
Torque specs
No owner-serviceable fasteners: verify — Dealer-only recall — Cummins fuel pump replacement; no owner torque specs apply.
Tips
1,737 trucks (2017-2018 Peterbilt 367, 389, 567, 579, 587; 2018 Kenworth C500, T680, T800, T880, W900 — all with Cummins ISX 15L): the fuel pump drive gear could slip on its drive shaft, causing fuel pump function loss and engine stall.
Remedy comes from Cummins: Cummins dealers replace the fuel pumps, free. The recall began July 1, 2017 (PACCAR C1909; Cummins 1-800-286-6467).
For the 579 the range is 2017-2018. This is the older sibling of 24V789 (2025 X15 fuel-pump barrel fracture): two Cummins fuel-pump campaigns on the 579, eight years apart, different failure modes — gear slip then, barrel fracture now.
Dealer-only recall repair — free at any Peterbilt dealer. Owner-side value: plastic tees in the fuel system: on 2017-2018 579/567s they can weep or leak diesel — a fuel smell with no obvious source points here.
Typical difficulty: Moderate — based on 483 code guides for the fuel repair area (an area-level estimate, not this exact job).
Torque specs
No owner-serviceable fasteners: verify — Dealer-only recall — plastic fuel tee replacement; no owner torque specs apply.
Tips
465 trucks (2015-2018 Kenworth K370, T680, T880; 2017-2018 Peterbilt 567, 579): the plastic fuel tee fittings may leak fuel.
Remedy: dealers replace the suspect fuel tees, free. The recall began April 13, 2017 (PACCAR 17KWA / 217-A).
For the 579 the range is 2017-2018 — the smallest population among the 579's fuel-system campaigns, which is exactly why it survives on trucks that missed it: fewer trucks, lower completion visibility. A diesel smell on a 2017-2018 579 with no wet lines at the filter head is worth a tee-fitting look.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
We don't have factory bulletin data for the 2017–2018 Peterbilt 579 yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.