Community-sourced DIY repair guides for the 2008–2008 Peterbilt 389, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Dealer-only recall repair — free at any Peterbilt dealer. Owner-side value: gear-tooth geometry, not assembly: the 2008 389's TRW TAS-85 steering gears may have the wrong tooth profile, chipping and damaging the gearing.
Typical difficulty: Moderate — based on 60 code guides for the steering repair area (an area-level estimate, not this exact job).
Torque specs
No owner-serviceable fasteners: verify — Dealer-only recall — TRW steering gear inspection/replacement; no owner torque specs apply.
Tips
559 trucks (2008 Kenworth and Peterbilt heavy-duty with TRW TAS-85 steering gears — Peterbilt 320, 365, 367, 384, 386, 387, 388, 389, 389K): the inner surface of the outer sector shaft teeth may have an incorrect involute profile, leading to chipping and damage of the gearing.
Remedy: dealers inspect and replace, free (PACCAR 1107K / 07KWE). Filed December 20, 2007 — the oldest campaign in this run.
For the 389 the range is 2008 only. Distinguish from the 2020s Sheppard-ball campaigns (22V547, 24V044): same symptom family (steering gear damage), different root cause — tooth geometry here, ball count there.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
What owners report
NHTSA recorded 3 complaints for the 2008–2008 Peterbilt 389. 2008 was the worst year (3 complaints). Most-reported areas: engine, service brakes, air.
13V593000 (25/11/2013) — EQUIPMENT:OTHER:LABELS Paccar Incorporated (Paccar) is recalling certain 2004-2013 Peterbilt 379, 357, 378, 367, 388, 365, 389, 385 and 386 trucks manufactured from April 3, 2003, through October 25, 2013 and equipped with tri-drive rear axles and a tag or pusher axle…
14V145000 (25/03/2014) — SERVICE BRAKES PACCAR, Inc. (PACCAR) is recalling certain model year 2008-2013 Peterbilt 365, 367, 388, 389 trucks manufactured October 6, 2007, through September 23, 2013. The affected vehicles were built with 16.5" x 7" front drum brakes and Bendix ES-420 brake linings…
08V487000 (23/09/2008) — ENGINE AND ENGINE COOLING:ENGINE:DIESEL PACCAR IS RECALLING 4,883 MY 2006-2009 KENWORTH T600, T660, T800, W900, T2000 AND MY 2008-2009 PETERBILT 365, 367, 379, 384, 386, 387, 388 AND 389 TRUCKS. INADEQUATE STIFFNESS OF THE DIESEL PARTICULATE FILTER (DPF) BRACKET COULD RESULT IN SEPARATION OF…
11V127000 (23/02/2011) — FUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY PACCAR IS RECALLING CERTAIN MODEL YEAR 2008-2012 KENWORTH T2000, T660, T700, T800, AND W900, AS WELL AS MODEL YEAR 2009-2012 PETERBILT 365, 367, 384, 386, 387, 388, 389, AND 587 TRUCKS EQUIPPED WITH PACCAR MX ENGINES. THE OIL MODULE CENTRIFUGAL…
07V591000 (20/12/2007) — STEERING:GEAR BOX:SHAFT SECTOR ON CERTAIN KENWORTH AND PETERBILT HEAVY DUTY TRUCKS EQUIPPED WITH TAS-85 TRW STEERING GEARS, THE INNER SURFACE OF THE OUTER SECTOR SHAFT TEETH OF THE STEERING GEARS MAY HAVE AN INCORRECT INVOLUTE PROFILE, WHICH MAY LEAD TO CHIPPING AND DAMAGE…
10V634000 (13/12/2010) — POWER TRAIN:AXLE ASSEMBLY PACCAR IS RECALLING CERTAIN MODEL YEAR 2007-2008 KENWORTH AND PETERBILT VEHICLES MANUFACTURED FROM FEBRUARY 2, 2006 THROUGH APRIL 30, 2007. THE BEARING SURFACES OF THE EXTENDED LUBE UNIVERSAL JOINT THAT ATTACHES THE INTER-AXLE DRIVELINE TO THE DRIVE AXLE MAY BECOME…
12 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
We don't have factory bulletin data for the 2008–2008 Peterbilt 389 yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.