2009–2020 Nissan 370Z

Community-sourced DIY repair guides for the 2009–2020 Nissan 370Z, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.

Owner-verified repair guides

Concentric slave cylinder (CSC) failure: pedal to the floor means the transmission comes out Owner-verified (3.7L VQ37VHR V6)

Diagnose first: clutch pedal to the floor (or spongy with no return) plus a low or empty clutch-fluid reservoir points at the internal CSC. Check under the car - fluid dripping directly below the transmission bellhousing confirms it. Plan a full transmission drop; there is no access cover. Pair the fix with a clutch replacement since the transmission is already out.

Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).

Torque specs

Tips

Sources: the370z.com 'Throw out bearing issue' - 2012 370Z clutch pedal fell straight to the floor with empty reservoir; members confirm 'the csc failure is a common issue' and the throwout bearing is part of the CSC unit · the370z.com DIY 'Video how to replace Clutch/Flywheel and Concentric slave cylinder' - 370Z-specific clutch/CSC replacement walkthrough; discussion covers ZSpeed CMAK vs JWT HD slave options · StraightSixImports ZSpeed CMAK V3 product page - 2009-2020 Nissan 370Z (6-speed manual) fitment; documents CSC failure symptoms (pedal to floor, soft/spongy pedal, fluid leaking inside bellhousing) and the external-slave delete fix

No owner reports yet — fixed this yourself? tell us how

VQ37VHR rear timing cover oil gallery gaskets: low oil pressure, P0011/P0021, VTC rattle Owner-verified (3.7L VQ37VHR V6)

This is a timing-cover-off job on the front of the engine. Confirm the diagnosis first with a mechanical oil-pressure gauge at the stock sender location: healthy VQ37VHR shows roughly 20-25+ psi at hot idle; a failed gallery gasket reads low at idle (dropping toward 10-15 psi) and stays low under load while the OEM low-pressure light stays off.

Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).

Torque specs

Tips

Sources: Z1 Motorsports 370Z/G37 VQ37VHR gallery gasket kit page - documents failure mode (paper gaskets seep, oil pressure drops, potential catastrophic engine failure) and symptoms: low gauge readings, P0011 or P0021 codes, excessive VTC rattle; fits 2009+ Nissan 370Z · the370z.com 'Low oil pressure!' thread - owner-tracked pressure drop at hot idle (25-20 psi down to 15, dipping to 10); members identify the gallery gaskets under the timing covers as the cause and report pressure doubling after replacement · VQPLUG steel gallery gasket set - direct-fit replacement for factory gaskets behind the timing cover; fitment lists 2009-2020 Nissan 370Z; notes OEM gaskets lose tension/warp causing internal oil pressure loss and extended startup rattle

P0011 on this Nissan 370Z — full diagnosis guide →

No owner reports yet — fixed this yourself? tell us how

Differential bushings: rear clunk and wheel hop from torn silicone-filled stock bushings Owner-verified (3.7L VQ37VHR V6)

Diagnose from underneath: the stock differential bushings are silicone-filled and tear under hard driving - look for black streaks of dried silicone on the rear subframe and a clunk/thunk from the rear under hard acceleration or launches. Replacement kits (polyurethane or solid) come with a bushing driver tool; an on-car remover/installer tool exists for doing the job without dropping the subframe.

Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).

Torque specs

Tips

Sources: GKTECH Z33/Z34 polyurethane diff bushings - Z34 370Z fitment; documents that diff movement within the subframe is common under hard driving and that polyurethane keeps it to a minimum; on-car install tool available · SPL Parts PRO solid differential bushings (2009-2020 Nissan 370Z Z34) - documents the stock silicone-filled bushing tearing under hard driving (black streaks of dried silicone on the rear subframe); Nissan/Infiniti do not sell the bushings separately; kit includes bushing driver tool · YouTube '370z Diff Bushing Replacement' - full walkthrough of removing and replacing a worn/blown differential bushing on a 370Z, including diff removal, forward and subframe bushing replacement, and torque specs

No owner reports yet — fixed this yourself? tell us how

Power window auto-up/anti-pinch lost after battery disconnect - reset procedure Owner-verified (3.7L VQ37VHR V6)

No parts or tools needed for the reset. Per the factory service manual (PWC section): close the door, turn the ignition ON (engine off), run the window fully down, then pull the switch to AUTO-UP and keep holding it for 3+ seconds after the glass is fully closed. Repeat for the other window, then check the anti-pinch function.

Torque specs

Tips

Sources: the370z.com 'Window going up and down' - owners document the window auto-adjust acting erratically after power loss; confirmed fix is the window reset procedure (ignition ON, run down, hold up 5 seconds), required after every battery disconnect · 2014 Nissan 370Z Factory Service Manual, PWC (Power Window Control System) section - documents the initialization procedure required after battery disconnect, control unit replacement, or motor/regulator removal: door closed, ignition ON, full open, then AUTO-UP held 3+ seconds past full close

No owner reports yet — fixed this yourself? tell us how

Fuel pump assembly and level senders: bad gauge readings and the blue o-ring seal Owner-verified (3.7L VQ37VHR V6)

Access is from inside the car, not underneath - remove the interior trim and the two access plates (passenger side: fuel pump module; driver side: fuel level sender). No fuel-tank drop is needed. Give yourself a full day for a first-time pump swap.

Typical difficulty: Moderate — based on 483 code guides for the fuel repair area (an area-level estimate, not this exact job).

Torque specs

Tips

Sources: the370z.com 'Gas gauge incorrect' - 370Z has TWO fuel level sensors whose readings are averaged; gauge errors come from a dislodged float, unseated T-fitting at the regulator outlet, and the blue o-ring seal that must not swell or be damaged or fuel leaks out on fill-up · the370z.com 'phunk's road race fuel pump install' - photo-documented 370Z fuel pump install: o-rings swell if left wet with fuel (wipe dry immediately), write down driver-side sender meter readings before disassembly, access via interior panels with seats removed

No owner reports yet — fixed this yourself? tell us how

Plastic coolant bleeder port / heater hose connector: brittle fitting that crumbles and dumps coolant Owner-verified (3.7L VQ37VHR V6)

The plastic heater-hose bleeder fitting sits in the heater hose run near the firewall. Replace it preemptively with an aluminum unit - order new spring clamps with it, as the originals can be stubborn to clear the hose indentation. The job is done from the engine bay.

Typical difficulty: Moderate — based on 294 code guides for the cooling repair area (an area-level estimate, not this exact job).

Torque specs

Tips

Sources: Z1 Motorsports aluminum coolant bleeder port (370Z fitment) - dozens of owner reviews document the OEM plastic fitting cracking, crumbling, and spraying the engine bay with coolant; aluminum replacement doubles as a coolant-bleeding aid · Concept Z Performance OEM heater coolant hose coupler (09+ 370Z Z34, 92417-JK20A) - documents the failure: the plastic couplers get brittle and break over time from heat cycling, resulting in lost coolant and potential overheating; CZP sells a billet aluminum upgrade

No owner reports yet — fixed this yourself? tell us how

Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

Codes on this 370Z

P0011
2009–2020 Nissan 370Z
VQ37VHR rear timing cover oil gallery gaskets: low oil pressure, P0011/P0021, VTC rattle
P0021
2009–2020 Nissan 370Z
VQ37VHR rear timing cover oil gallery gaskets: low oil pressure, P0011/P0021, VTC rattle

What owners report

NHTSA recorded 19 complaints for the 2009–2020 Nissan 370Z. 2012 was the worst year (16 complaints). Most-reported areas: power train, air bags, engine.

Counts are NHTSA complaints filed for these model years, via the NHTSA API. See data for all 370Z years →

Factory service bulletins

We don't have factory bulletin data for the 2009–2020 Nissan 370Z yet.

Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.

Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.