Community-sourced DIY repair guides for the 2020–2024 Mercedes-Benz GLS, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
EVAP purge valve sits on the driver side of the engine, right under the air intake duct. Reachable from above with the engine cover off.
Typical difficulty: Moderate — based on 483 code guides for the fuel repair area (an area-level estimate, not this exact job).
Torque specs
EVAP purge valve: verify — Mounting torque not confirmed from an owner source — confirm against factory service info; the valve is a light press/clip-fit part, do not overtighten.
Tips
If you hear a ticking noise from the engine at idle, check the EVAP purge valve before assuming lifters or injectors: owners on the X167 GLS forum traced the tick to the purge valve under the air intake duct on the driver side.
The two-minute confirmation test: with the engine idling and ticking, unplug the electrical connector on the purge valve — if the ticking stops, the valve is the culprit.
The fix is a cheap valve swap, roughly $75 for the part. Mercedes revised the design — ask for the updated part number 001-470-09-93-64 rather than a like-for-like of the old one. One owner's dealer replaced it at no charge under warranty.
Multiple owners describe this as a very common failure across many Mercedes models (GLE, GLS, and others) from years back through the 2023/2024 model years — so a used GLS with this tick is showing a known wear item, not a dying engine.
Advanced DIY: needs a 9G-specific fill adapter, the multi-position drain plug tool, and a scanner for fluid temperature and valve flushing. Very doable for a serious DIYer.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Tips
The X167 GLS uses the 725.0 9G-Tronic. The drain plug is a multi-position standpipe: you need the special valve tool to move it to the correct position for draining vs. level-checking - watch how the plug rotates before touching anything.
Drain the torque converter plug as well, not just the pan - skipping it leaves several liters of old ATF in the system.
On the 9G the plastic oil sump is replaced as a unit (the filter is built in); the MEYLE kit ships the sump with filter, seals and magnets pre-installed, which is the shortcut owners use.
You need a diagnostic scanner to run the valve-flushing routine (brake pedal pressed, engine running) and to read live ATF temperature - final fluid level is set with the engine running at 35-45°C; too cold or too hot and the level will be wrong.
Scan for transmission fault codes and test-drive before the service; owners recommend changing fluid well before any shift-quality complaints appear - the 9G is far less tolerant of degraded fluid than the old 7G.
4MATIC transfer case fluid service Owner-verified(3.0L M256 I6 turbo + EQ Boost, 4.0L M176 V8 + EQ Boost)
Easy driveway DIY: drain and fill through the plugs; the gotcha is the clutch pack and the fluid spec, not the wrenching.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Tips
Get the fluid spec right for your VIN via operatingfluids.mercedes-benz.com - dealer parts counters are reported as unreliable for drivetrain oils. Owners report: rear axle 75W-85 spec 235.7 or 239.71 (light-alloy housing), front axle 75W-85 spec 239.72, transfer case spec 236.12 (236.14 reported back-compatible) while another owner used 239.41 - confirm before filling.
If you get a groaning noise at parking-lot speeds while turning after the change, you need to change the transfer case fluid a SECOND time: the clutch pack that varies front/rear torque needs the first change to clean the clutch plates and the second to reset the fluid. Owners report MB's own guidance is to keep changing until the noise is gone.
Check drain/fill plug access before you start - it can be tight on the X167; a manual fluid pump and a hex set are the required tools.
Buy new transfer case plugs (the video owner sourced them from FCP Euro) - the plugs are one-time crush/plastic types on these trucks.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
We don't have factory bulletin data for the 2020–2024 Mercedes-Benz GLS yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.