Community-sourced DIY repair guides for the 2019–2020 Mercedes-Benz A-Class, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Dealer-only - the dealer installs the inspection gauge and provides supplemental owner's manual pages. Nothing for the owner to remove or adjust.
Typical difficulty: Moderate — based on 265 code guides for the brake repair area (an area-level estimate, not this exact job).
Torque specs
Brake pad inspection gauge: verify — Dealer-installed recall part - no owner torque values needed.
Tips
NHTSA recall 23V-732 (announced November 2023, 42,742 vehicles) covers the 2019-2020 A220 along with the CLA250, GLB250, AMG A35/CLA35/CLA45 and 2021 GLA250: the rear brake pads shipped without the inspection gauge used to check pad wear, and the owner's manual lacks the gauge instructions.
The rear pads on these cars have no dashboard wear sensor, so without the gauge there is no reliable way to know when the pads are worn - driving on worn pads reduces braking ability.
The remedy is free: the dealer installs the inspection gauge and hands you supplemental manual pages. Owner letters were mailed February 29, 2024.
If your 2019-2020 A220 has never had this done, book it with your next service - and check the rear pads by the gauge at every oil change, since there is no dash warning to save you.
Diagnosis is scan-first: a code reader that talks to the transmission module should show a selector-module fault. The replacement module itself is a dealer part and typically needs coding to the car.
Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).
Torque specs
Selector module fasteners: verify — Dealer part with coding - torque specs not confirmed from an owner source; confirm against factory service info before torquing.
Tips
The signature symptom, reported by three A220 owners on the mbworld A-Class thread: push the start button, the dash lights and screens come on, but the starter never engages - no clicking, nothing. The white box around P R N D on the instrument cluster disappears so you cannot tell what gear is selected, and the cluster may show 'transmission is not in park' or 'close the door' messages even though moving the column shifter does nothing.
The cause is the electronic selector module failing to report the current gear position to the ECU - the car thinks it is not in Park and refuses to start. One owner had the car towed within its first 400 miles and the dealer replaced the transmission selector module, which fixed it.
Before assuming the worst, rule out the cheap causes: press the brake pedal firmly (the brake switch is part of the start interlock), try the key fob in the cup-holder slot with the key symbol imprinted at the base, and check that the shift lever is fully seated in Park.
If the PRND indicator is missing from the cluster and the brake switch checks out, the selector module is the prime suspect - have the transmission module scanned for stored codes rather than replacing the battery or starter first.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
What owners report
NHTSA recorded 21 complaints for the 2019–2020 Mercedes-Benz A-Class. 2020 was the worst year (21 complaints). Most-reported areas: electrical system, engine, power train.
We don't have factory bulletin data for the 2019–2020 Mercedes-Benz A-Class yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.