Community-sourced DIY repair guides for the 2024–2025 Mazda CX-90, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
No DIY repair here — this is a dealer recall visit, and a federal investigation is still open on whether the recall fix actually works. If your steering effort changes suddenly or feels sticky mid-turn, treat it as a safety issue: get to the dealer and file a complaint with NHTSA if it happens after the recall work.
Typical difficulty: Moderate — based on 60 code guides for the steering repair area (an area-level estimate, not this exact job).
NHTSA recall 24V022 (January 2024, about 44,000 CX-90s): an assembly issue with the worm gear in the electric power steering could cause a sudden and unexpected change in steering effort — or a sudden loss of power steering assist — while driving.
Mazda's stated cause was a spring in the steering assembly pushing too hard on a gear. The dealer remedy replaced the spring, regreased the gears, and reassembled the motor.
NHTSA opened a federal investigation after receiving 26 reports of 'sticky steering' — sudden increases in steering effort — from drivers whose vehicles had already received the 24V022 remedy. At least two crashes were linked.
The problem has been reported on some 2025 models and PHEV versions too. If you had the recall done and the steering still feels notchy or sticky, report it to NHTSA — that is exactly what the investigation is collecting.
Check recall status by VIN at nhtsa.gov/recalls before paying for any steering diagnosis. This is free dealer work, including the re-inspection if symptoms persist.
There is no owner-serviceable adjustment for this — the fix is a dealer TCM reflash done with Mazda's diagnostic system. Your job as the owner is recognizing the symptom pattern and asking for the bulletin by name: a harsh 1-2 shift that is worst when the transmission is cold and fades as it warms up.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Mazda TSB (2024 CX-90 H3T, VINs below JM3KJ******110311 / built before May 22, 2024): some owners get a shift shock on the 1-2 shift when the vehicle is cold (ATF at or below 86°F / 30°C), caused by improper hydraulic pressure control in the 8-speed. The fix is a TCM software reprogram.
A CX-90 owner on the forums reported the dealer found an 'SSPD2 transmission solenoid concern,' updated the module software per the bulletin, and the car drove 'like a totally different car' afterward — the low-speed bucking and hesitation after near-stops was more or less cured.
MotorTrend's long-term CX-90 PHEV showed the same family of symptoms independently: shudder and hesitation after full stops and at slow speeds, plus hard abrupt shifts in EV mode and a stumble in the EV-to-hybrid transition.
The TSB repair procedure also calls for performing any open campaign PCM reprograms first — the dealer may reflash PCM and TCM together as one software package, so ask them to check for open campaigns at the same visit.
After the reprogram, a pending DTC P2610 may store in the PCM without a check-engine light; the bulletin says to clear codes after all work is done, so don't panic if a scan shows it right after the visit.
The leak is at the back of the engine where the turbocharger oil drain-back tube meets the block — it looks like a rear main seal or bell-housing leak, so confirm the source before assuming the worst. Dealer repair requires catalytic converter removal to reach the tube; the bolts are one-time-use (new bolts come with thread sealer already applied).
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Torque specs
Turbo drain-back tube bolts: 95 in-lbs (11 N·m) — One-time-use bolts; new bolts come with thread sealer pre-applied. Degrease holes and gasket surface first.
Tips
Mazda service alert (2024–2025 CX-90 H3T): engine oil can leak from the rear of the engine at the turbocharger drain-back tube. The bolt holes are drilled through into the engine and thread sealer was not properly applied at the factory, so oil wicks past the bolt threads.
This is easy to misdiagnose as a leak from behind the bell housing (rear main seal). If you see oil at the back of the engine, have the drain-back tube area checked before authorizing a rear-main job.
The fix is new bolts (pre-coated with thread sealer — the old ones must not be reused) plus a new gasket, with the bolt holes and gasket surface fully degreased before reassembly.
Access requires removing the catalytic converter to reach the tube, so this is a lift job even though the parts are cheap.
No owner repair — this is a dealer TSB visit. What you can do: note the exact conditions (cold weather, first start of the day, warning lights) and the stored codes, and don't keep cycling the start button — have it towed to the dealer if it won't enter READY mode.
Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).
Torque specs
TSB connector repair: verify — Dealer-performed TSB; no owner torque specs apply. Do not open high-voltage connectors yourself.
Tips
Mazda TSB 09-027-26 (2024–2026 CX-90 PHEV): the vehicle may fail to start — won't enter READY mode — in cold weather, though it often starts fine on the next attempt. Stored codes can include P0AB9, U0100, U0110, and U0115 with multiple warning lights.
Root cause per the bulletin: water reaching the 3002-411 connector in the luggage compartment corrodes the terminals, creating leakage current that makes the Battery ECU falsely detect the MAIN relay as ON — so it refuses to activate READY mode.
The factory countermeasure is urethane added around the connector to keep water off the terminals; the dealer repair addresses the corroded connector per the bulletin.
If your PHEV intermittently refuses to go READY on cold mornings with a Christmas tree of warning lights, mention this TSB by number — it's a known pattern, not a dying high-voltage battery.
Owner habit, not a wrench job: when you power the car on, actually activate the EV system (READY indication in the cluster) instead of just cycling the ignition. If the car sits, start it to READY at least as often as the bulletin schedule says.
Typical difficulty: Involved — based on 854 code guides for the battery repair area (an area-level estimate, not this exact job).
Typical time: “For a CX-90 PHEV that sits or gets its doors opened and closed a lot without being driven (showroom-style use), the bulletin calls for activating the EV system about an hour every morning.” — as written in the note. First-timers often take twice this.
Torque specs
12V battery service: verify — Standard 12V battery work only; never open high-voltage system components.
Tips
Mazda service alert on PHEV 12V (lead-acid) battery care: the 12V battery is charged from the high-voltage battery only while the EV system is activated. Turning the power on repeatedly without activating the EV system can drain the 12V completely — then the ignition won't turn on and the EV system can't activate at all.
For a CX-90 PHEV that sits or gets its doors opened and closed a lot without being driven (showroom-style use), the bulletin calls for activating the EV system about an hour every morning.
If the high-voltage battery state of charge is below 1%, charge it to 10% (plug in or run the engine) — a depleted HV pack can't keep the 12V topped up.
Symptom pattern owners hit: car was fine yesterday, today it's completely dead with no response from the start button after a lot of door-opening/loading without driving. That's the 12V, not the hybrid battery — jump or charge the 12V and change the habit.
Check with the under-covers off: look for ATF seepage around the transmission thermo valve. The dealer fix is a new gasket and a higher torque on the valve; about 2 fl oz (50 ml) of ATF drips out by gravity during the swap, and the ATF level must be re-adjusted afterward.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Mazda TSB (2024 CX-90 3.3L MHEV, VINs below JM3KK******155319 / built before December 21, 2023): technicians may find ATF seeping from the automatic transmission at the thermo valve when the under-covers come off.
Cause is insufficient tightening torque on the thermo valve from the factory. Mazda revised the spec upward — the old 52–59 ft-lbs is superseded.
The repair is a new gasket plus the revised torque. Expect roughly 2 fl oz (50 ml) of ATF to drip out by gravity while the valve is off — keep your face clear and have a catch container ready, then adjust the ATF level per the workshop manual procedure afterward.
No DIY fix — this is a dealer BCM software update. Your part is noticing the symptom: if the fuel gauge doesn't match how much fuel you actually used (especially right after fill-up or on a long trip), get the recall done rather than trusting the needle.
Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).
NHTSA recall 25V568 (2024–2025 CX-90 mild-hybrid models): the instrument-cluster fuel gauge can display an inaccurate fuel reading due to body control module software.
An optimistic gauge is a run-out-of-fuel risk and a pessimistic one just causes anxiety — either way, don't diagnose a 'bad fuel sender' yourself until the recall software is applied.
Check recall status by VIN at nhtsa.gov/recalls; the dealer reflash is free.
PHEV drive-power loss recall 23V719 — check VIN first Factory-documented(2.5L PHEV)
No DIY repair — this is a dealer software recall. If your PHEV ever loses drive power suddenly or the engine and motor shut down together unexpectedly, get it to the dealer and make sure this recall is closed on your VIN before authorizing any other powertrain diagnosis.
Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).
Torque specs
Recall software update: verify — Dealer-performed recall; no owner torque specs apply. Do not open high-voltage components.
Tips
NHTSA recall 23V719 (2024 CX-90 PHEV): a software error can cause the engine and the electric motor to shut down unexpectedly, resulting in a sudden loss of drive power.
A related campaign, 24V817, covers improper inverter software on 2024 CX-90 / 2025 CX-70 PHEVs that can light the malfunction indicators and drop drive power while in EV mode — ask the dealer to check both on your VIN.
Because the root cause is software, there is no owner-side part to replace or reset — the fix is the dealer reflash, and it's free under the recall.
Check recall status by VIN at nhtsa.gov/recalls before paying for any hybrid-system diagnosis.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
We don't have factory bulletin data for the 2024–2025 Mazda CX-90 yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.