Community-sourced DIY repair guides for the 2020–2022 Kia Telluride, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Rear suspension — self-leveling Nivomat shocks are standard on the factory towing package. The first fix is done under the insulator TSB; full shock replacement is a bolt-on dealer job if the clunk persists.
Typical difficulty: Moderate — based on 27 code guides for the suspension repair area (an area-level estimate, not this exact job).
Torque specs
Rear shock absorber mounting bolts: 94 lb·ft (127 N·m) — Per the TSB PDF.
Rear shock absorber lock nut: 16 lb·ft (22 N·m) — Per the TSB PDF; nut is one-time use, do not reuse.
Tips
The signature is a rattle or clunk from the rear on rough roads or pulling out of the driveway, often appearing after using a hitch tray or towing; Nivomat-equipped tow-package Tellurides are the repeat population.
The documented ladder: Kia TSB-113 (202201) first — dealers replace the rear shock insulators; if the noise survives, the follow-on TSB 25-SS-003H directs replacing both rear shock absorbers. Multiple owners report the insulator TSB alone did not fix theirs, and shock replacement did.
Some owners with failed repeat sets swapped to conventional (non-Nivomat) shocks and springs — the clunk disappears, at the cost of losing the self-leveling function. Do not do this as the first move while warranty coverage is still available.
Do not let a dealer stop at the insulator TSB if the clunk persists — the published procedure escalates to shock replacement. Ask for the case to be documented each visit if the noise returns, since repeat failures are reported.
Tow-hitch harness fire recall (Kia 22V-626) Owner-verified(3.8L Lambda II V6)
The harness module sits at the rear tow-hitch area. No DIY fix exists for the defect itself — the action is: check your VIN, confirm whether the harness was installed, and follow the recall remedy.
Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).
NHTSA 22V-626 / Kia SC263 covers 36,417 Tellurides (2020-2022) with the genuine Kia 4-pin tow-hitch harness accessory. Moisture and foreign-material contamination on the module's printed circuit board can cause a short and fire — parked or driving.
This is the Kia-side campaign, distinct from the Palisade's Hyundai 22V-633 campaign — same defect family, separate NHTSA number. Kia documented six fires, five with localized melting only, all on 2020s; 2021-2022s were included as a precaution.
Park outside and away from structures until the repair is done — the recall notice says so explicitly, and unlike the Palisade side Kia had no interim fuse-pull repair available at launch.
Check whether your vehicle actually has the harness: the 4-pin version was discontinued as a port-installed option after 2020 and sold as a dealer-installed accessory for 2021-2022, so affected VINs were not all identifiable up front. Enter the VIN at nhtsa.gov/recalls.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
What owners report
NHTSA recorded 763 complaints for the 2020–2022 Kia Telluride. 2020 was the worst year (763 complaints). Most-reported areas: exterior lighting, engine, unknown or other.
20V436000 (28/07/2020) — ELECTRICAL SYSTEM:WIRING Kia Motors America (Kia) is recalling certain 2020 Telluride vehicles equipped with Smart Cruise Control (SCC). When a trailer is connected to the vehicle, the trailer brake lights will not illuminate when the SCC applies the brakes. As such, these…
24V148000 (26/02/2024) — EXTERIOR LIGHTING:HEADLIGHTS Kia America, Inc. (Kia) is recalling certain 2020 Telluride vehicles. The high beam headlights may fail.
24V214000 (20/03/2024) — POWER TRAIN:DRIVELINE:DRIVESHAFT Kia America, Inc. (Kia) is recalling certain 2020-2024 Telluride vehicles. The intermediate shaft and right front driveshaft may not be fully engaged, which can result in vehicle roll away while in PARK.
22V626000 (15/08/2022) — TRAILER HITCHES Kia America, Inc. (Kia) is recalling certain 2020-2022 Telluride vehicles potentially equipped with a Genuine Kia 4-pin tow hitch harness installed as original equipment, or purchased as an accessory through a Kia dealership. Debris and moisture accumulation on the tow…
19V594000 (13/08/2019) — SEAT BELTS:REAR/OTHER Kia Motors America (Kia) is recalling certain 2020 Telluride vehicles. The seat belt assemblies in the front passenger, second, and/or third row seats may not tightly secure a child restraint system in the event of a crash. As such, these…
24V407000 (05/06/2024) — SEATS:FRONT ASSEMBLY:POWER ADJUST Kia America, Inc. (Kia) is recalling certain 2020-2024 Telluride vehicles. The front power seat motor may overheat due to a stuck power seat slide knob, which can result in a fire while parked or driving.
7 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
We don't have factory bulletin data for the 2020–2022 Kia Telluride yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.