Community-sourced DIY repair guides for the 2017–2022 Kia Sportage, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Owner-verified repair guides
Notchy / sticky steering at speed Owner-verified(2.4L Theta II GDI, 2.0L Theta II T-GDI)
From below with the car on ramps: pull the small undertray in the middle of the car (4x 10mm bolts), then the 3x 10mm bolts on the steering rack/box cover sitting just above the subframe under a heat shield. Tight working room, but the heat shield does not need to come off.
Typical difficulty: Moderate — based on 60 code guides for the steering repair area (an area-level estimate, not this exact job).
Torque specs
Rack/box cover bolts and undertray bolts (10mm): verify — Bolt torque not confirmed from a source — these are small cover fasteners; confirm against factory service info before torquing.
Tips
Learn the feel: the steering catches slightly around center and goes heavier-then-lighter on small corrections, worst at motorway speeds. QL (2016-2022) Sportages are known for developing this as the steering rack/box runs dry of grease.
The documented fix follows the Kia technical bulletin the dealers use: get to the rack/box cover above the subframe and pack it with grease. Two independent DIYers filmed exactly this on the QL Sportage (one also confirmed it on the Tucson twin) and report the notchiness gone afterward.
If greasing does not fully cure it, there is a second documented path: one UK owner's heavy AND notchy steering — a pain since delivery — was transformed when the dealer recalibrated the power steering sensor after ruling out alignment. Ask for the EPS sensor calibration check before anyone sells you a replacement rack.
Do not confuse this with the MDPS coupler clunk (covered on the Sonata run): the coupler is a knocking sound when turning the wheel, this is a sticky/notchy feel through the wheel with no noise.
Access note from the guide: only the smaller middle undertray needs removing (4x 10mm bolts), then 3x 10mm bolts on the rack/box cover. It is tight but a 10mm ring spanner reaches without removing the heat shield.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
What owners report
NHTSA recorded 161 complaints for the 2017–2022 Kia Sportage. 2020 was the worst year (161 complaints). Most-reported areas: engine, unknown or other, electrical system.
22V703000 (19/09/2022) — TRAILER HITCHES Kia America, Inc. (Kia) is recalling certain 2016-2022 Sorento, 2021-2022 Sorento Hybrid (HEV), 2022-2023 Sorento Plug-In Hybrid (PHEV), and 2017-2022 Sportage vehicles equipped with a tow hitch harness installed as original equipment, or purchased as an accessory through a Kia…
21V137000 (04/03/2021) — SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:CONTROL UNIT/MODULE Kia Motors America (Kia) is recalling certain 2017-2021 Sportage and Cadenza vehicles. The electrical circuit in the Hydraulic Electronic Control Unit (HECU) may short-circuit, which can cause a fire in the engine compartment.
2 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
We don't have factory bulletin data for the 2017–2022 Kia Sportage yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.