Community-sourced DIY repair guides for the 2018–2024 Kenworth W900, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Owner-verified repair guides
Extra spacer in seat-to-belt-tether joint may leave the connection unsecured (23V-717 / PACCAR 23KWK) Factory-documented(12.9L PACCAR MX-13 diesel (405–510 hp), Cummins X15 diesel (400–605 hp))
Dealer-only recall repair — free at any Kenworth dealer. Owner-side value: 3,841 trucks. An additional spacer may have been added at the joint connecting the seat to the seat belt tether and buckle — the connection is not what the torque spec thinks it is. The dealer removes the spacer and replaces the bolt, free.
Typical difficulty: Moderate — based on 119 code guides for the restraints repair area (an area-level estimate, not this exact job).
Torque specs
No owner-serviceable fasteners: verify — Dealer repair only; no owner repair. Free at any Kenworth dealer.
Tips
The unsecured seat-to-belt-tether joint can separate in a crash — the belt anchor is only as good as its bolt.
Kenworth filing 23KWK; dealers inspect, remove the spacer, and replace the bolt free of charge (letters mailed Mar 20, 2024).
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
What owners report
NHTSA recorded 1 complaints for the 2018–2024 Kenworth W900. 2024 was the worst year (1 complaints). Most-reported areas: fuel system, diesel.
23V717000 (26/10/2023) — SEAT BELTS PACCAR Incorporated (PACCAR) is recalling certain 2020 Kenworth T660, 2018-2024 Kenworth T800 and W900 vehicles. An additional spacer may have been added to the joint that connects the seat to the seat belt tether and buckle, causing an unsecured connection.
20V506000 (26/08/2020) — POWER TRAIN:AXLE ASSEMBLY PACCAR Incorporated (PACCAR) is recalling certain 2020-2021 Peterbilt 348, 365, 367, 389, 520, 567 and Kenworth T800, T880, W900, W990 vehicles equipped with Watson and Chalin steerable lift axle suspension systems (model SL2065). The axles may have lower rear pivot…
22V277000 (25/04/2022) — STEERING:CRITICAL FASTENERS PACCAR Incorporated (PACCAR) is recalling certain 2018-2020 Kenworth T270, T370, T440, T470, T660, T680, T880, T800, W900, W990; and 2018-2020 Peterbilt 330, 337, 348, 365, 367, 389, 520, 567, and 579 vehicles. The Dana D-Series axle steer arm fasteners that…
24V043000 (25/01/2024) — STEERING:LINKAGES:KNUCKLE:SPINDLE:ARM PACCAR Incorporated (PACCAR) is recalling certain 2024 Peterbilt 367, 389, 520, 567, and Kenworth T800, T880, W900, and W990 trucks. The bearing journals may not be fully seated in the steering knuckle assemblies, preventing the proper installation of the wheel…
20V199000 (06/04/2020) — ELECTRONIC STABILITY CONTROL (ESC) PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with…
19V176000 (05/03/2019) — SUSPENSION:REAR:AXLE:NON-POWERED AXLE ASSEMBLY PACCAR Incorporated (PACCAR) is recalling certain 2020 Kenworth T680, T800, T880, W900 and W990 trucks. The rear axles may not contain oil.
7 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
We don't have factory bulletin data for the 2018–2024 Kenworth W900 yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.