Community-sourced DIY repair guides for the 2022–2024 Jeep Grand Wagoneer, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
The dealer inspects the left and center third-row buckles; if a buckle is damaged or cannot be accessed, they replace it. Labor runs 0.2 hr for inspection and up to 1.0 hr for both replacements.
Torque specs
Seatbelt buckle hardware: verify — Torque specs for buckle fasteners not confirmed from a source — confirm against factory service info before torquing.
Tips
FCA recall A7A / NHTSA 23V-716 covers about 104,400 model year 2022-2024 Wagoneer and Grand Wagoneer SUVs: the third-row left and center seatbelt buckles may have been built with buckles that are inaccessible or damaged, so an occupant cannot fasten the belt.
An inaccessible or damaged buckle leaves the occupant unrestrained in a crash. Check the third row yourself: if a buckle has sunk into the seat trim or will not latch, stop using that seat and get it inspected.
The dealer fix is free: they inspect both buckles (0.2 hr labor) and replace any bad ones. If parts are not on hand, the dealer is supposed to leave the repair order open and have you return once the parts arrive.
Because the affected population is large but the defect rate within it is not stated, confirm your VIN is on the campaign list before assuming coverage.
Both are software-only fixes done by the dealer (or via recall notice). The 23V577 remedy updates the Central Vision Park Assist module; the D5B remedy reprograms the Rearview Camera Module.
Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).
Torque specs
Camera module fasteners (if replaced): verify — No torque-critical fasteners in the software-remedy path; confirm against factory service info if a module is physically replaced.
Tips
The Grand Wagoneer has been hit by two overlapping rearview-camera recalls. Recall 56A / NHTSA 23V-577 (August 2023, 162,713 vehicles including 2022-2024 Wagoneer/Grand Wagoneer) found that Central Vision Park Assist module (CVPAM) software can prevent the rear image from displaying in reverse — an FMVSS 111 violation.
A second campaign, D5B / NHTSA 24V-944, covers 2024 models (20,550 Wagoneer/Grand Wagoneer) whose Rearview Camera Module shipped with incorrectly programmed software that also blocks the reverse image; remedy is a dealer reprogram, launched early 2025.
If your camera ever goes blank or blue in reverse, both fixes are free dealer software updates. Because these are successive campaigns on overlapping vehicles, a truck 'repaired' under the first recall should still be checked against the second — enter the VIN on nhtsa.gov rather than assuming you are covered.
There is no DIY fix path: the root cause is module software, not a loose connector, and owner reports consistently show dealer reprogramming is the resolution.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
What owners report
NHTSA recorded 34 complaints for the 2022–2024 Jeep Grand Wagoneer. 2024 was the worst year (34 complaints). Most-reported areas: electrical system, engine, unknown or other.
23V716000 (26/10/2023) — SEAT BELTS: REAR/OTHER:BUCKLE ASSEMBLY Chrysler (FCA US, LLC) is recalling certain 2022-2024 Jeep Wagoneer and Grand Wagoneer vehicles. The third-row seat belts may not allow occupants to properly access or fasten the seat belt to the buckle. As such, these vehicles fail to comply…
25V642000 (25/09/2025) — STRUCTURE:EXTERIOR TRIM Chrysler (FCA US, LLC) is recalling certain 2022-2024 Jeep Wagoneer and Jeep Grand Wagoneer vehicles. The quarter trim on the driver and passenger windows may not have been properly secured, which can allow it to detach.
24V944000 (19/12/2024) — BACK OVER PREVENTION:SOFTWARE Chrysler (FCA US, LLC) is recalling certain 2024 Jeep Wagoneer, Grand Wagoneer, Grand Cherokee, and Grand Cherokee L vehicles. Incorrect software in the rearview camera module may cause the rearview camera image not to display. As such, these vehicles fail…
23V577000 (14/08/2023) — BACK OVER PREVENTION:DISPLAY FUNCTION Chrysler (FCA US, LLC) is recalling certain 2022-2023 Jeep Grand Cherokee, 2021-2023 Jeep Grand Cherokee L, and 2022-2024 Jeep Wagoneer and Grand Wagoneer vehicles. The Central Vision Park Assist module (CVPAM) software may prevent the rearview image from displaying when…
24V199000 (14/03/2024) — AIR BAGS:FRONTAL:DRIVER CLOCKSPRING/SPIRAL CASSETTE Chrysler (FCA US, LLC) (Stellantis) is recalling certain 2023-2024 Ram 1500, Jeep Wrangler, Jeep Wagoneer, Jeep Grand Wagoneer, Chrysler Pacifica, Ram 3500, Ram 3500 cab chassis, Ram 2500, Ram 4500 cab chassis, Ram 5500 cab chassis, 2023 Jeep Gladiator, Jeep…
25V593000 (11/09/2025) — STRUCTURE:EXTERIOR TRIM Chrysler (FCA US, LLC) is recalling certain 2022-2025 Jeep Wagoneer and Jeep Grand Wagoneer vehicles. The trim on the driver and passenger doors may not have been installed properly, which can allow it to detach.
8 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
We don't have factory bulletin data for the 2022–2024 Jeep Grand Wagoneer yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.