Community-sourced DIY repair guides for the 2019–2021 International RH, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Dealer-only recall repair — free at any International dealer. Owner-side value: the RED engine warning light from the revised knock-detection software means STOP the engine as soon as it is safe — and defective rods are repaired under the A26's 500,000-mile engine warranty.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Torque specs
No owner-serviceable fasteners: verify — Dealer-only recall — revised knock-detection software and connecting rod repair; no owner torque specs apply.
Tips
10,038 trucks in the US (10,828 with Canada) — 2019-2021 LT and RH: the second wave of the A26 wrist-pin saga, April 2021. The wrist pin bore was machined outside the design tolerance for straightness; over time the bushing cracks or loses chunks, and the connecting rod fails. About 17% of the affected A26 engines were expected to experience the failure.
The revised fix is what distinguishes wave two: new knock-detection system software that warns the driver BEFORE connecting rod failure. A red engine warning light means stop the engine as soon as it is safe — that lamp is the whole point of the software, so don't ignore it and don't keep running to the next exit.
Critical administrative detail: trucks already repaired under wave one (20V-255) that got the earlier calibration or no detection system must RETURN for this revised software. The 20V-255 fix is superseded. Engines found with a suspect connecting rod are repaired under the engine's 500,000-mile warranty — know your warranty before authorizing anything out of pocket.
Owner letters mailed July 2021 (Navistar 21505). Wave three (22V-691) followed in September 2022 and widened the net again — see the companion note. A 2019-2021 A26 RH should show the full sequence closed.
BCM software error may let truck overcome the parking brake (23V-119 / Navistar 23503) Factory-documented(12.4L International A26 diesel (370–475 hp), Cummins X15 diesel (400–605 hp))
Dealer-only recall repair — free at any International dealer. Owner-side value: this is the PTO-truck recall — if your RH runs a PTO (dump, mixer, refuse body), the failure scenario is engine-revving during PTO operation overpowering the set parking brake. Chock wheels until the BCM update is done.
Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).
Torque specs
No owner-serviceable fasteners: verify — Dealer-only recall — BCM software update; no owner torque specs apply.
Tips
4,199 trucks (2018-2021 HV, 2019-2021 RH, 2019-2022 MV, 2022 HX): a software error in the Body Control Module may allow the vehicle to OVERCOME the parking brake during power-take-off (PTO) operation. A parking brake that does not hold can let the vehicle move unexpectedly — the crash and injury risk the campaign is built around.
The real-world trigger was mundane and instructive: a customer complained that a vehicle upfit as a cement mixer unexpectedly moved after the engine speed was ramped up to begin pouring concrete. Regional-haul RHs are exactly the trucks that get PTO bodies — this campaign matters more for the RH line than the headline population suggests.
Remedy: dealers update the BCM software, free of charge. Owner notification letters were mailed April 24, 2023; Navistar's number is 23503, NHTSA's 23V-119. (The sibling 23V-120, filed the same day for a Cummins ECM PTO parameter on HV/MV/TC, does NOT include the RH — documented as a rejection, not an RH campaign.)
The majority of the population is HV models — the RH slice is smaller, but the PTO exposure is what makes this one worth knowing. Until repaired: chock the wheels whenever the PTO is engaged.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
We don't have factory bulletin data for the 2019–2021 International RH yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.