Community-sourced DIY repair guides for the 2018–2019 International RH, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Owner-verified repair guides
Seat belt anchor D-ring bolt may break in a crash — FMVSS 210 (18V-293 / Navistar 18505) Factory-documented(12.4L International A26 diesel (370–475 hp), Cummins X15 diesel (400–605 hp))
Dealer-only recall repair — free at any International dealer. Owner-side value: the defect was caught ON the assembly line (broken bolts at Springfield) — but 18,665 trucks had already shipped, so a used 2018-2019 RH still needs the VIN check.
Typical difficulty: Moderate — based on 119 code guides for the restraints repair area (an area-level estimate, not this exact job).
Torque specs
No owner-serviceable fasteners: verify — Dealer-only recall — seat belt D-ring bolt replacement; no owner torque specs apply.
Tips
18,665 trucks and buses (2018-2019 WorkStar, DuraStar, LoneStar, LT, ProStar, RH, TranStar, HV/MV, IC Bus HC): the front driver and passenger seat-belt anchor D-ring bolt can break in a crash, leaving the occupant unrestrained — a FMVSS 210 (seat belt assembly anchorages) noncompliance. Navistar estimates only about 1% of the population actually has the bad bolts.
The backstory is a manufacturing detective story: in March 2018 Navistar found broken D-ring bolts DURING ASSEMBLY at the Springfield plant, quarantined vehicles there, ran metallurgical testing, then quarantined the Escobedo plant and the parts distribution centers too. Supplier: Shield of Elkhart, Indiana. The recall (April 26, 2018 declaration) swept up everything already shipped with suspect bolts.
Remedy depends on the seat-belt label: dealers replace the D-ring bolt per the information on the label, free. Recall began May 23, 2018 (Navistar 18505); 14,863 of 18,665 were remedied by Q3 2019.
For the RH the range is 2018-2019. It's a quick dealer visit — and on a used-truck inspection, an open 18V-293 is a five-minute VIN check that speaks to whether the previous owner kept up with campaigns generally.
Eaton ECA clutch internal failure may cause unintended movement (18V-826 / Navistar 18518) Factory-documented(12.4L International A26 diesel (370–475 hp), Cummins X15 diesel (400–605 hp))
Dealer-only recall repair — free at any International dealer. Owner-side value: the fix here is SOFTWARE, not a clutch job — if a dealer quotes clutch replacement for this campaign, they're wrong; the remedy is a TCM recalibration.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Torque specs
No owner-serviceable fasteners: verify — Dealer-only recall — TCM recalibration (software only); no owner torque specs apply.
Tips
21,740 trucks (2019 HV/MV, 2018-2019 HX/LT/RH/LoneStar/ProStar/WorkStar, 2018 TranStar) with Eaton ECA heavy-duty automated-manual clutches: an internal clutch component can fail, and the failure mode is unintended vehicle movement — the truck can move when the driver doesn't expect it to.
The owner-relevant surprise: the remedy is a Transmission Control Module RECALIBRATION — software, not hardware. No clutch gets replaced under this campaign. If anyone quotes you a clutch job for 18V-826, that's not the recall remedy.
The RH range is 2018-2019 — launch-era trucks. Press reports at the time cited ~20,916 trucks; NHTSA's current record shows 21,740 potentially affected.
Recall began January 18, 2019 (Navistar 18518). With most of the population now seven-plus years old, this campaign is mainly a used-truck check now: verify 18V-826 is closed on any 2018-2019 RH before purchase.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
We don't have factory bulletin data for the 2018–2019 International RH yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.