Community-sourced DIY repair guides for the 2018–2019 International LT, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Owner-verified repair guides
Eaton ECA clutch internal failure may cause unintended movement (18V-826 / Navistar 18518) Factory-documented(12.4L International A26 diesel (370–475 hp), Cummins X15 diesel (400–605 hp))
Dealer-only recall repair — free at any International dealer. Owner-side value: the fix here is SOFTWARE, not a clutch job — if a dealer quotes clutch replacement for this campaign, they're wrong; the remedy is a TCM recalibration.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Torque specs
No owner-serviceable fasteners: verify — Dealer-only recall — TCM recalibration (software only); no owner torque specs apply.
Tips
21,740 trucks (2019 HV/MV, 2018-2019 HX/LT/RH/LoneStar/ProStar/WorkStar, 2018 TranStar) with Eaton ECA heavy-duty automated-manual clutches: an internal clutch component can fail, and the failure mode is unintended vehicle movement — the truck can move when the driver doesn't expect it to.
The owner-relevant surprise: the remedy is a Transmission Control Module RECALIBRATION — software, not hardware. No clutch gets replaced under this campaign. If anyone quotes you a clutch job for 18V-826, that's not the recall remedy.
Affected LTs were built April 20, 2017 through July 21, 2018 — essentially launch-era trucks. Press reports at the time cited ~20,916 trucks; NHTSA's current record shows 21,740 potentially affected.
Recall began January 18, 2019 (Navistar 18518). With most of the population now seven-plus years old, this campaign is mainly a used-truck check now: verify 18V-826 is closed on any 2018-2019 LT before purchase.
Cummins ISX15/X15 fuel line may burst if cooling screen clogs (18V-588 / Cummins-issued) Factory-documented(Cummins ISX15/X15 diesel (400–605 hp))
Dealer-only recall repair — free; owners are notified BY CUMMINS (not Navistar) since this is a Cummins-issued campaign. Owner-side value: this is an engine-supplier defect, so the same failure can appear on any ISX15/X15-powered truck — but the free steel-line fix runs through the Cummins/International channel for these VINs.
Typical difficulty: Moderate — based on 483 code guides for the fuel repair area (an area-level estimate, not this exact job).
Torque specs
No owner-serviceable fasteners: verify — Dealer-only recall — nylon-to-steel fuel line replacement (Cummins channel); no owner torque specs apply.
Tips
26,288 trucks — 2018-2019 LT, 2017-2019 LoneStar/HX, 2017-2018 ProStar/9900i, 2017 PayStar — all with Cummins ISX15 or X15 engines: on long downhill grades, the fuel pump cooling circuit screen can become restricted, and the NYLON fuel line can burst. Consequences stack up fast: engine stall, fuel spill on the roadway, fire risk.
This is a CUMMINS campaign, not a Navistar one — NHTSA's record carries no Navistar mfr number, and Cummins notifies the owners directly (Cummins customer service 1-800-286-6467). The remedy replaces the nylon fuel line with a STEEL fuel line, free. Interim owner notification went out October 11, 2018; the recall began November 21, 2018.
Corroboration that this is a Cummins-population defect: Daimler recalled 4,500 of its own trucks for the identical fuel-pump cooling-circuit issue in the same period. Any used X15/ISX15 truck from this era deserves the fuel-line material checked, regardless of badge.
For the LT specifically the population is 2018-2019 model years. Given the age of these trucks now, verify the steel-line remedy was actually performed — a surviving original nylon line on a downhill-heavy route is the risk case this recall was built for.
Dealer-only recall repair — free at any International dealer. Owner-side value: this one is visually inspectable by the owner — open the hood and look at the fuel/water separator inlet fitting for rub or abrasion marks from the splash panel.
Typical difficulty: Moderate — based on 483 code guides for the fuel repair area (an area-level estimate, not this exact job).
Torque specs
No owner-serviceable fasteners: verify — Dealer-only recall — splash panel trim and inlet line replacement; no owner torque specs apply.
Tips
527 trucks — and this one is LT-ONLY: with the hood closed, the fender splash panel rubs on the inlet fuel-line fitting to the fuel/water separator, abrading the fitting until it leaks fuel. Fuel leak plus ignition source is a fire risk; fuel on the roadway is a crash risk.
The population is defined by separator hardware: 483-model separators (feature codes 0015LMC/LMD/LNC/LND/LPK) with drum brakes, or 488-model separators (0015LNL/LNM/LPL). Navistar estimated 100% of the 527-truck population had the interference condition — every truck in the net needed the fix.
The owner-DIY angle is real here: open the hood and inspect the fuel/water separator inlet fitting for rub marks or abrasion from the splash panel. It's a visible, checkable condition — exactly the kind of thing to look at on a used 2018-2019 LT.
Remedy: dealers trim the splash panel for clearance and replace any damaged fuel/water inlet line, free. 505 of 527 were remedied by Q3 2019 — one of the best completion rates in the LT file. Recall began May 14, 2018 (Navistar 18503).
Seat belt anchor D-ring bolt may break in a crash — FMVSS 210 (18V-293 / Navistar 18505) Factory-documented(12.4L International A26 diesel (370–475 hp), Cummins X15 diesel (400–605 hp))
Dealer-only recall repair — free at any International dealer. Owner-side value: the defect was caught ON the assembly line (broken bolts at Springfield) — but 18,665 trucks had already shipped, so a used 2018-2019 LT still needs the VIN check.
Typical difficulty: Moderate — based on 119 code guides for the restraints repair area (an area-level estimate, not this exact job).
Torque specs
No owner-serviceable fasteners: verify — Dealer-only recall — seat belt D-ring bolt replacement; no owner torque specs apply.
Tips
18,665 trucks and buses (2018-2019 WorkStar, DuraStar, LoneStar, LT, ProStar, RH, TranStar, HV/MV, IC Bus HC): the front driver and passenger seat-belt anchor D-ring bolt can break in a crash, leaving the occupant unrestrained — a FMVSS 210 (seat belt assembly anchorages) noncompliance. Navistar estimates only about 1% of the population actually has the bad bolts.
The backstory is a manufacturing detective story: in March 2018 Navistar found broken D-ring bolts DURING ASSEMBLY at the Springfield plant, quarantined vehicles there, ran metallurgical testing, then quarantined the Escobedo plant and the parts distribution centers too. Supplier: Shield of Elkhart, Indiana. The recall (April 26, 2018 declaration) swept up everything already shipped with suspect bolts.
Remedy depends on the seat-belt label: dealers replace the D-ring bolt per the information on the label, free. Recall began May 23, 2018 (Navistar 18505); 14,863 of 18,665 were remedied by Q3 2019.
For the LT the range is 2018-2019. It's a quick dealer visit — and on a used-truck inspection, an open 18V-293 is a five-minute VIN check that speaks to whether the previous owner kept up with campaigns generally.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
What owners report
NHTSA recorded 2 complaints for the 2018–2019 International LT. 2019 was the worst year (2 complaints). Most-reported areas: engine, power train, service brakes.
18V199000 (29/03/2018) — FUEL SYSTEM, DIESEL Navistar, Inc. (Navistar) is recalling certain 2018-2019 International LT trucks. When the hood is in the closed position, the fender splash panel may rub on the inlet fuel line fitting to the fuel/water separator, causing abrasion damage to the fitting…
22V546000 (28/07/2022) — ELECTRICAL SYSTEM:12V/24V/48V BATTERY:CABLES Navistar, Inc. (Navistar) is recalling certain 2018-2021 International LoneStar and 2016-2021 International LT vehicles. The cables that connect the batteries to the vehicle frame may become excessively hot, and in some cases, cause battery post separation.
19V122000 (26/02/2019) — ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE Navistar, Inc. (Navistar) is recalling certain 2016-2020 International LT and 2017-2018 Prostar 73-inch sleeper cab models equipped with feature code 07BKP or 07BKR (exhaust system with horizontal after treatment device and horizontal tailpipe mounted on right side). In the affected…
25V817000 (25/11/2025) — ELECTRICAL SYSTEM:SOFTWARE International Motors, LLC (International) is recalling certain 2016 7600, 2016-2023 Lonestar, 2018 8600, 2018-2023 LT, 2021-2026 MV, 2022-2023 RH, 2023-2026 HX, and 2025-2026 HV vehicles. Electrical noise and low signal to the power line carrier may cause the ECU to…
21V281000 (22/04/2021) — ENGINE Navistar, Inc. (Navistar) is recalling certain 2019-2021 International LT and RH trucks. The wrist pin may crack and cause connecting rod failure.
18V826000 (21/11/2018) — POWER TRAIN:CLUTCH ASSEMBLY Navistar, Inc. (Navistar) is recalling certain 2019 International HV, MV, 2018-2019 HX, LT, RH, LoneStar, ProStar, WorkStar, and 2018 TranStar automated manual transmission vehicles, equipped with certain Eaton ECA heavy-duty truck clutches. An internal component in the clutch assembly may…
18 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
We don't have factory bulletin data for the 2018–2019 International LT yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.