Community-sourced DIY repair guides for the 2014–2020 Infiniti QX60, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Driveway-diagnosable: the shudder is unmistakable once you know what to feel for; the fix itself (valve body or replacement) is shop work, but catching it early and knowing the service history is pure owner value.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Tips
The signature failure starts as a judder or shake accelerating between 20 and 40 mph - the internal steel belt slipping on the pulleys. It worsens as friction debris clogs the valve body and overheats the fluid.
Other telltales: hesitation or lag off the line, a whining noise from the transmission, or the car dropping into limp mode with power severely restricted.
The 2013-2014 JX35/QX60 and Pathfinder CVTs drew a class-action settlement (2016) over violent shudder and jerking from alleged JATCO CVT8HT belt slip; a separate suit covers 2019-2021 models. Nissan never recalled them.
2014 and 2015 are the worst years (82 and 33 NHTSA-pattern complaints on the QX60); 2019+ CVT logic improved and the CVT was dropped entirely for the 2022 9-speed.
DIY value: test-drive for the 20-40 mph shudder before buying used, pull the CVT service history, and do preventive NS-3 drain-and-fills - once it shudders hard the fix is a valve body or a $3,000-$8,000 replacement.
CVT NS-3 drain-and-fill: ~4 qt per dump, level-set at temp Owner-verified(3.5L VQ35DE (2014-2016), 3.5L VQ35DD direct-injection (2017-2020))
Easy driveway job: drain plug and fill port are accessible; the only fussy part is getting the car perfectly level on four stands and setting the level at the right fluid temperature.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Typical time: “Dealer charges $250-$350 for this service; DIY is fluid plus an hour of your time.” — as written in the note. First-timers often take twice this.
Tips
Each dump removes only ~3.6-4 quarts - less than half the total capacity - so think of it as a refresh, not a flush. Repeat every 30k-50k miles; one owner does 4 drain/fills between 25k and 45k miles.
Use NS-3-spec fluid only (genuine Nissan NS-3 or Idemitsu NS3). The wrong fluid will kill a CVT.
The level must be set with the car perfectly level and the fluid at the specified temperature - one owner used an Android OBD app to read CVT temp and set the level per the service manual.
The transmission pan drain plug uses the same size copper washer as the engine oil pan, and the level-check port bolt has a reusable rubber O-ring.
2015+ (and late 2014) cars got a revised CVT pan with no dipstick in the charge port and a different drain port location - confirm which pan you have before starting.
Dealer charges $250-$350 for this service; DIY is fluid plus an hour of your time.
Rear clunk/vibration on turns: electric AWD coupler TSB Owner-verified(3.5L VQ35DE (2014-2016), 3.5L VQ35DD direct-injection (2017-2020))
Driveway-diagnosable in minutes with the TSB's unplug-and-retest procedure; the coupler swap itself is a patient Saturday job on jack stands.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Tips
The symptom: a binding feeling, vibration, or clunking from the rear when turning at low speed or accelerating from a stop, on AWD models.
The factory diagnosis is simple and owner-doable: unplug the actuator assembly on the rear final drive unit and retest. If the noise goes away, the electrohydraulic coupling is the culprit.
The TSB warns that mismatched tires (different size, brand, or tread pattern) cause identical symptoms - if you replaced tires, make sure all four match before condemning the coupler.
The owner fix: swap the coupling assembly - jack and stands, 14mm socket and wrench, 8mm hex, oil catch pan, soft hammer, and patience. Part numbers are documented in the video description.
An Infiniti dealer will follow the same TSB; knowing the unplug test lets you walk in with the diagnosis already confirmed.
Transfer case gear-oil flush by 60k mi (AWD only) Owner-verified(3.5L VQ35DE (2014-2016), 3.5L VQ35DD direct-injection (2017-2020))
Easy driveway service: two hex plugs, a gear-oil pump, and a level car. Do the fill plug first - if it will not budge, stop before draining.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Tips
AWD QX60s have a small transfer case that holds only a few ounces of gear oil - owners report it loads up with wear metals on the first services. By the time you notice a leak, the unit has usually run dry and is finished.
Service it no later than 100,000 km / 60,000 miles, and consider it more important than the CVT fluid itself - the transfer case is in motion any time the vehicle moves.
Golden rule: remove the FILL plug first, then the drain plug. Never drain what you cannot refill.
You need a 10mm hex bit, a gear-oil pump to get fluid back in, a drain pan, and the car level.
One QX60 owner did transfer case and rear differential at 47,000 km as preventive maintenance and plans repeats - treat it as a wear item, not lifetime fill.
Spark plugs: intake plenum must come off for the rear bank Owner-verified(3.5L VQ35DE (2014-2016), 3.5L VQ35DD direct-injection (2017-2020))
Moderate 2-3 hour driveway job. The front bank is trivial; the rear bank is under the intake plenum, so budget most of the time for plenum removal and reassembly.
Typical difficulty: Easy — based on 64 code guides for the ignition repair area (an area-level estimate, not this exact job).
Typical time: “Moderate 2-3 hour driveway job.” — as written in the note. First-timers often take twice this.
Tips
The rear bank sits under the intake plenum - there is no shortcut. Remove the engine cover (10mm), air intake, throttle body (T30 Torx), and the intake manifold (12mm bolts) to reach it.
Always install a new intake manifold/plenum gasket on reassembly, and keep debris out of the open intake ports while you work.
Use OEM iridium plugs - Denso 3442 is the documented fit for the 2013-2016 VQ35DE; 2017-2020 cars run the direct-injection VQ35DD, so match the plug to your engine and verify the part number before ordering.
Do coils at the same time if you are past 100k miles - you are already paying the labor to get to them.
Blow out the plug wells with compressed air BEFORE removing plugs - debris falls in easily on this engine.
Misfire codes P0300-P0306, rough idle, or hesitation under load on a high-mileage QX60 point here first.
Driveway-diagnosable and a straightforward pad-and-rotor job; the hard lesson in this thread is the lug-nut discipline, not the parts.
Typical difficulty: Moderate — based on 265 code guides for the brake repair area (an area-level estimate, not this exact job).
Torque specs
Lug nuts: verify - 2016 QX60 owner used 83 ft-lbs — Always finish lug nuts with a torque wrench in a star pattern (two passes); impact guns over-torque and cause the runout behind brake judder.
Tips
Judder is rotor thickness variation, not necessarily a 'warped' rotor - one owner's turned rotors measured only 0.004 in removed and were judged not warped, yet the judder persisted through three rotor sets.
The thread's hard-won lesson: an impact gun easily over-torques lug nuts to twice spec, and the heat-cycling then deforms the rotor. Finish every wheel with a torque wrench in a star pattern.
Infiniti's brake TSB ITB00-024 (amended through 2023, applies to all Infiniti vehicles including the QX60) covers rotor indexing and judder diagnosis - a dealer tech in the thread confirms it is general good-practice guidance, not a QX60-specific defect.
When you do the job: 17mm caliper bolts, 19mm bracket bolts; clean the hub and rotor mating faces of rust and grit before assembly; bleed in order rear-passenger, rear-driver, front-passenger, front-driver; bed the pads in with repeated 60-to-10 mph stops.
If judder survives new rotors plus torque discipline, check hub runout with a dial indicator and the wheel bearings - the dealer in the thread misdiagnosed a hub bearing once.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
NHTSA recorded 53 complaints for the 2014–2020 Infiniti QX60. 2016 was the worst year (29 complaints). Most-reported areas: air bags, unknown or other, power train.
21V402000 (27/05/2021) — SUSPENSION:REAR:AXLE:SPINDLE Nissan North America, Inc. (Nissan) is recalling certain 2020 Nissan Murano, INFINITI QX60, 2021 Nissan GT-R, INFINITI QX50, and Q50 vehicles. The front steering knuckle or rear axle housing may have insufficient strength due to improper heat-treatment.
16V244000 (26/04/2016) — AIR BAGS:SENSOR:OCCUPANT CLASSIFICATION Nissan North America, Inc. (Nissan) is recalling certain model year 2016-2017 Nissan Maxima, 2013-2016 Nissan Altima, NV200, LEAF, Sentra, and Pathfinder, 2014-2016 Nissan NV200 Taxi, Infiniti QX60, QX60 Hybrid, and Q50 Hybrid, 2014-2017 Nissan Rogue and Infiniti Q50, 2015-2016 Nissan…
2 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
We don't have factory bulletin data for the 2014–2020 Infiniti QX60 yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.