Community-sourced DIY repair guides for the 2016–2021 Infiniti Q50, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Owner-verified repair guides
Accessory belt shredding/flung off from misaligned A/C compressor; updated lipped idler pulley Owner-verified(3.0L VR30DDTT twin-turbo V6)
Front of the engine: inspect belt and pulleys, verify A/C compressor alignment, replace belt and the smooth idler pulley with the updated lipped design. Look up fastener specs in the Q50 FSM - do not guess.
Torque specs
Accessory belt fasteners (tensioner, idler, compressor): verify — Do not guess - look up in the Q50 FSM (EM section) and use a torque wrench.
Tips
If the belt is squealing/screeching under load around 3-3.5k rpm - or shredding or walking off - check A/C compressor alignment, not just the belt. Replacing only the belt on a misaligned compressor invites a repeat.
The documented permanent fix is the updated smooth idler pulley with tall lips on the front and rear (vendor documents p/n 11925-6HL0A, Bando belt) - the lips keep the belt from walking off where the old flat design let it wander.
Do not confuse this with turbo whistle: belt noise is a constant engine-speed screech; turbo whistle follows boost. Several owners in the turbo thread chased the wrong one.
A flung or shredded belt can take out the accessories it drives, so treat sudden belt noise as park-it-soon, not ignore-it.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
What owners report
NHTSA recorded 42 complaints for the 2016–2021 Infiniti Q50. 2016 was the worst year (39 complaints). Most-reported areas: engine, electrical system, steering.
17V476000 (27/07/2017) — FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP Nissan North America, Inc. (Nissan) is recalling certain 2016-2018 Infiniti Q50 and 2017 Infiniti Q60 vehicles equipped with a 2.0L engine. Incorrect Fuel Pump Control Module (FPCM) software may allow the fuel level in the main tank to be too…
16V244000 (26/04/2016) — AIR BAGS:SENSOR:OCCUPANT CLASSIFICATION Nissan North America, Inc. (Nissan) is recalling certain model year 2016-2017 Nissan Maxima, 2013-2016 Nissan Altima, NV200, LEAF, Sentra, and Pathfinder, 2014-2016 Nissan NV200 Taxi, Infiniti QX60, QX60 Hybrid, and Q50 Hybrid, 2014-2017 Nissan Rogue and Infiniti Q50, 2015-2016 Nissan…
24V470000 (21/06/2024) — POWER TRAIN:DRIVELINE:DRIVESHAFT Nissan North America, Inc. (INFINITI) is recalling certain 2011-2013 M56, 2012-2013 M35 Hybrid, 2014-2018 Q50, Q70 Hybrid, 2014-2019 Q70, and 2015-2019 Q70L two-wheel drive vehicles. The driveshaft can fatigue and break.
16V430000 (13/06/2016) — STEERING:AUTOMATED/ADAPTIVE STEERING Nissan North America, Inc.'s (Nissan) is recalling certain model year 2014-2016 Infiniti Q50 vehicles manufactured December 26, 2012, to December 11, 2015, and Infiniti Q50 Hybrid vehicles manufactured December 10, 2012, to December 17, 2015. The Direct Adaptive Steering system…
4 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
We don't have factory bulletin data for the 2016–2021 Infiniti Q50 yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.