Community-sourced DIY repair guides for the 2022–2022 Hyundai Santa Cruz, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Owner-verified repair guides
DCT failsafe / loss of drive power (recall) Factory-documented(2.5T Smartstream T-GDI)
All recall work is dealer-performed: dealers inspect the transmission and update the transmission control unit software, replacing the transmission where needed. There is no driveway repair for the root cause.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Torque specs
Transmission R&R: verify — Dealer service only; no owner torque specs involved.
Tips
The failure signature: dash warning lights plus a warning message, then the truck drops into a fail-safe mode where drive power fades over about 30 seconds and then cuts out completely, leaving the truck immobilized.
The defect is an internal fault in the 8-speed wet dual-clutch transmission's high-pressure electric oil pump, which corrupts the fail-safe drive mode so it cannot keep the truck rolling to safety.
The recall covers 9,142 Santa Cruz units within 53,142 affected Hyundai vehicles (2021-2022 Santa Fe, Sonata, Veloster N, Elantra N, Kona N plus the 2022 Santa Cruz). Owner letters went out in December 2022.
Check your VIN against campaign 22V746000 (Hyundai recall 236); Hyundai customer service is 1-855-371-9460. This is unrelated to the earlier turbo oil-pipe recall.
Do not confuse failsafe-mode immobilization with the DCT's normal low-speed lumpiness at parking-lot speeds: lumpiness is a characteristic of this gearbox, sudden power loss with warning lights is the recall defect.
Dealer-performed: the turbocharger oil supply pipe is swapped for one built to the correct material specification. No owner labor involved.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Torque specs
Turbo oil supply pipe: verify — Dealer-installed per the recall remedy; no owner torque specs involved.
Tips
The oil supply pipe to the turbocharger was produced with insufficient material thickness, which can let it crack and leak oil onto hot engine and exhaust components, creating a fire risk.
This was a tiny, early-production recall: only 16 vehicles (11 Santa Cruz and 5 Santa Fe), all built between March 2 and March 7, 2022, and caught before delivery to owners.
Dealers replace the pipe with the same part built to the correct material specification, free of charge. Owner letters were mailed May 26, 2022.
A used-oil smell or visible oil around the turbo on a very early 2022 2.5T Santa Cruz is worth checking against campaign 22V197000 (Hyundai recall 222) before chasing gaskets or seals.
If you own one of the affected trucks, call Hyundai customer service at 1-855-371-9460 with the VIN; parts backorders hit other early Santa Cruz recalls, so ask about parts availability when scheduling.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
We don't have factory bulletin data for the 2022–2022 Hyundai Santa Cruz yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.