Community-sourced DIY repair guides for the 1999–2009 Honda S2000, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Owner-verified repair guides
Timing-chain tensioner (TCT) rattle: replace or repair it before the chain jumps Owner-verified(2.0L F20C I4, 2.2L F22C1 I4)
Remove the stock airbox for access (10mm/8mm sockets), unbolt the tensioner from the front of the head, and either swap a new/modified unit in or sandblast the worm gear of your old one per the DIY. About an hour with the airbox method.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Typical time: “About an hour with the airbox method.” — as written in the note. First-timers often take twice this.
Tips
The failure mode is the worm gear inside the TCT wearing so it no longer holds tension: metallic raspy rattle on a warm/hot startup that rises and falls with the gas pedal and fades as you drive. Cold-morning startups often sound fine - that's why owners miss it.
Your options, in community order of preference: (1) buy a new OEM TCT and sandblast its worm gear before install, (2) sandblast your existing one ($10 of sand), (3) buy a Billman/Spitfire-modified TCT (~$240-250, guaranteed for life), (4) bolt in a new stock TCT and accept it will fail again.
This is not a 'live with it' noise: if the rattle becomes constant, the timing chain can jump and the engine is likely ruined. The job is ~1 hour and 3/8-drive sockets with 10mm/8mm - dealer quotes of $200-800 are pure labor markup.
The high-lift-cam/forced-induction warning: a weak stock TCT also can't hold tension with aggressive cams or boost - if you're modding, the modified/billet tensioner is the expected baseline.
The deceleration 'buzz' is normal gear backlash - don't buy a clutch for it Owner-verified(2.0L F20C I4, 2.2L F22C1 I4)
No part to swap for a fix - it's a diagnostic judgment call. If the noise matches the TSB symptom (decel, 3rd/2nd, 3-4k rpm, vanishes with a touch of throttle or clutch), the honest move is to confirm it matches and drive on rather than throw a clutch at it.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Tips
Symptom signature: buzzing/rattling from the transmission tunnel while decelerating in 3rd or 2nd between roughly 3,000-4,500 rpm; it goes away if you press the accelerator lightly or disengage the clutch. It's loudest because the gearbox sits between the seats, not up front.
Cause per Honda: normal clearance (backlash) between transmission gears, excited by engine pulses on decel; the four springs in the clutch-disc hub vibrate and amplify it. It causes no damage and will not blow the engine.
Honda issued TSB 00-054 for MY2000-01 with an improved clutch disc (P/N 22200-PCX-005) that quiets it - but even owners with the updated disc report the noise returning within days/weeks of a clutch job. It is not reliably 'fixable' with parts.
Do not misdiagnose it as a failing throwout bearing or bad gear: those don't vanish with a touch of throttle. If it matches the signature above, save your money.
Rear tires dying fast? The factory rear toe spec is the killer - align it down Owner-verified(2.0L F20C I4, 2.2L F22C1 I4)
Alignment shop, with a printout of what you want: total rear toe-in well under the stock AP1 spec (many owners run ~0.2 degrees total, i.e. ~3/32 inch total). Zero front toe, near-zero rear toe is the tire-life recipe.
Typical difficulty: Moderate — based on 60 code guides for the steering repair area (an area-level estimate, not this exact job).
Tips
The S2000's stock AP1 rear-toe range (roughly 0.33-0.67 degrees total toe-in) is far more than a street car needs - it scrubs the inside of the rear tires and is the number-one reason rears die in 7-10k miles on a daily driver.
The community consensus street spec: ~0.2 degrees TOTAL rear toe-in (about 3/32 inch total, half the stock midpoint), zero front toe, and rear camber in the -1 to -2 degree range. Toe kills tires far faster than camber, so toe is the number you negotiate.
Honda published a ServiceNews bulletin on premature rear tire wear - this is a documented vehicle trait, not your driving.
All four corners are factory-adjustable (camber, caster, toe) - no aftermarket kits needed for a street alignment; bring the shop a written spec sheet because 'set it to factory' is what put the killer toe in.
Tires are staggered and directional on the S2000 - Honda says never rotate them (per Honda ServiceNews), so alignment is your only tire-life lever.
Click/pop from the rear on takeoff or direction change: re-torque the rear axle nuts Owner-verified(2.0L F20C I4, 2.2L F22C1 I4)
Handbrake on, in gear, wheel on the ground (or tire just touching). Pop the center cap, remove the 36mm staked axle nut with a long breaker bar, clean and lightly grease threads + washer faces, install a NEW nut, torque, and re-stake. Do both sides.
Typical difficulty: Moderate — based on 27 code guides for the suspension repair area (an area-level estimate, not this exact job).
Torque specs
Rear axle nut: 200 ft-lbs + 60 degrees turn (Honda revised TSB spec; many experienced owners torque to ~220-221 lb-ft) — 36mm staked nut. Clean + lightly grease threads and washer faces first; always use a NEW nut and re-stake after torquing. Do both sides.
Tips
The signature: one or two sharp clicks/pops from the rear when launching from a stop or changing direction (forward to reverse) - often described as 'two metal marbles'. It's the wheel bearing shifting inside the hub because the axle nut has loosened.
This affects ALL years - AP1s came under-torqued from the factory and even late AP2s (a 2009 with 11k miles checked by a shop owner) showed loose nuts.
Torque spec: Honda revised it from 180 to 200 ft-lbs PLUS 60 degrees of turn (cited from the TSB in the S2000 common-problems list). Many experienced owners torque to ~220-221 lb-ft instead - either way, always use a NEW staked nut (36mm) and stake it after torquing.
If the click has been ignored a long time and there's now a rotational noise or wobble too, the bearing/hub or CV joint may be damaged and the re-torque alone won't cure it - but re-torquing first costs nothing.
If clicking persists after a proper re-torque on both sides, the differential/diff mounts and prop shaft are the next suspects - see the diff-fluid note for the first maintenance step back there.
Misfire codes: swap-test the coil packs before buying anything Owner-verified(2.0L F20C I4, 2.2L F22C1 I4)
Coil packs sit on the plugs under the plug cover - swap a suspect coil to a good cylinder, clear the code, and see if the misfire follows the coil. One 10mm bolt and a connector each; no special tools.
Typical difficulty: Easy — based on 64 code guides for the ignition repair area (an area-level estimate, not this exact job).
Tips
On 100k+ mile S2000s, coil packs are a wear item: the community rule is coils fail more often than injectors clog, so ignition gets checked before fuel.
The free test: clear the code, swap the coil from the misfiring cylinder with one from a good cylinder, drive it, re-scan. If the misfire code follows the coil, buy that coil. If it stays, the coil is innocent - check plugs, compression, then injectors.
A ticking sound from the coil area after a code can mean arcing (pack-to-plug or inside the pack) - inspect before replacing; owners report plenty of good packs get replaced unnecessarily.
If one coil is dead at 100k+, budget for the other three soon - they tend to go in sequence. Keep the old working ones as trail spares.
Flashing CEL + misfire: stay under ~3k rpm on the drive home to protect the cat, then diagnose - don't keep driving it hard.
Solid lifters need periodic valve adjustment - and tight valves are silent killers Owner-verified(2.0L F20C I4, 2.2L F22C1 I4)
Valve cover off, engine cold, feeler gauges. The cover comes off easily (this is the 'valve adjustment day' job owners do in a driveway) - measure all 16, adjust the tight/loose ones to spec with the locknut adjusters, new valve-cover gasket on reassembly.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Typical time: “Owners report ~1 hour once they've done it.” — as written in the note. First-timers often take twice this.
Tips
The F20C/F22C use solid lifters (screw-and-locknut adjusters), so valve clearance is a maintenance item, not lifetime. Honda's book interval is 105k miles 'unless noisy' - the community treats that as too long, especially on a 20-year-old car.
Critical subtlety: these engines' clearances TIGHTEN with mileage, which means they get quieter, not louder - waiting for 'noise' misses the danger. Tight valves burn: one owner found valves three gauges too tight with a lumpy idle.
The 2006-2009 AP2 cars deserve extra attention: they're reported to run leaner and can have dangerously tight clearances from the factory - checking at purchase is cheap insurance.
It's a genuinely easy DIY: valve cover off, cold engine, feeler gauges, adjust with the screw/locknut. Owners report ~1 hour once they've done it. Always fit a new valve-cover gasket on reassembly.
While the cover is off on an AP1, do the retainer check too (see the valve-retainer note) - it's the same teardown.
Differential fluid: 30k-mile service with GL-5, not GL-4/MTF Owner-verified(2.0L F20C I4, 2.2L F22C1 I4)
Fill plug first (23mm), then drain (24mm socket - it has the magnet). Drain, refill with GL-5 hypoid gear oil until it weeps from the fill hole. Takes about 1 quart; no lift needed for most owners.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Tips
The S2000's Torsen diff takes GL-5 hypoid gear oil (SAE 90 / 75W-90 / 75W-110) - NOT GL-4 and NOT Honda MTF, which is for the gearbox. Using a non-GL5 fluid in the diff will cause problems.
Honda never made its own GL5 hypoid oil for the S2000 (and published a bulletin when GL6 gear oil wasn't available for it) - so a quality aftermarket GL5 is the correct answer, not a dealer part.
Interval: 30,000 miles or 2 years, whichever first; 15,000 miles severe service. Most owners change it more often than the book - it's one quart and a 20-minute driveway job.
The drain bolt has the magnet, the fill bolt doesn't - open the FILL first; if you can't open it, don't drain. The 2006+ maintenance minder shows code B6 for this service.
If you're chasing a rear clunk, drain the diff and look at the fluid/magnet first - broken pinion teeth show up fast in the drain pan.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
NHTSA recorded 162 complaints for the 1999–2009 Honda S2000. 2000 was the worst year (46 complaints). Most-reported areas: power train, engine and engine cooling, air bags.
06V270000 (26/07/2006) — EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL ON CERTAIN PASSENGER VEHICLES AND MOTORCYCLES, THE OWNER'S MANUALS CONTAIN INCORRECT CONTACT INFORMATION FOR THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION'S (NHTSA) VEHICLE SAFETY HOTLINE.
00V016000 (24/01/2000) — SEAT BELTS:FRONT:ANCHORAGE VEHICLE DESCRIPTION: CONVERTIBLE PASSENGER VEHICLES. WHEN THE CONVERTIBLE TOP IS DOWN AND THE SEAT IS PUSHED ALL THE WAY BACK, THE SEAT BELTS MAY NOT RETRACT PROPERLY RESULTING IN SLACK IN THE SEAT BELTS.
13V246000 (13/06/2013) — SERVICE BRAKES, HYDRAULIC:POWER ASSIST:VACUUM American Honda Motor Co., Inc. (Honda) is recalling certain model year 2006 Acura RSX vehicles manufactured January 18, 2006, through August 12, 2006; and model year 2006-2007 Honda S2000 vehicles manufactured January 19, 2006, through November 13, 2006. The brake…
00V316000 (10/10/2000) — SEAT BELTS:FRONT:RETRACTOR VEHICLE DESCRIPTION: PASSENGER VEHICLES. UNDER CERTAIN CONDITIONS, THE SEAT BELT RETRACTOR CAN DEFORM AND CAUSE COMPLETE OR FREQUENT LOCKING OF THE RETRACTOR. AS A RESULT, THE SEAT BELTS CANNOT BE PULLED OUT OF THE RETRACTOR AND CANNOT BE USED.
04V257000 (01/06/2004) — EXTERIOR LIGHTING:TAIL LIGHTS CERTAIN PASSENGER VEHICLES FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THE LENS OF THE SIDE MARKER LAMP AND SIDE REFLEX REFLECTOR IN THE TAIL LAMP ASSEMBLY WERE…
5 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
We don't have factory bulletin data for the 1999–2009 Honda S2000 yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.