Community-sourced DIY repair guides for the 2024–2025 Honda Prologue, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Owner-verified repair guides
Rearview camera blank/distorted (recall) Factory-documented(85 kWh Ultium FWD/AWD)
Dealer-only recall. A blank or distorted backup camera reduces rear visibility — take extra care reversing until the camera is replaced.
Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).
Torque specs
Rearview camera fasteners: verify — Dealer replaces the camera assembly — no owner torque procedure published.
Tips
NHTSA campaign 26V306000 (Honda DO5/DO6), announced May 14, 2026: the rearview camera housing may be improperly bonded, so the adhesive can separate over time. Moisture then gets in and corrodes internal electrical components, making the image blurry, distorted, or blank. 59,887 vehicles are involved, including 44,199 Honda Prologue 2024–2025s.
Honda had 2,411 warranty claims for the issue and investigated it jointly with GM for about two years before recalling. No injuries were reported.
Unlike the earlier 26V112000 software recall, this is a hardware defect — it cannot be fixed over the air. Dealers replace the rearview camera with an improved, properly sealed part free of charge. Improved cameras went into production June 9, 2025.
Owner letters were mailed July 6, 2026. Check your VIN at nhtsa.gov or call Honda customer service at 1-888-234-2138.
Dealer repair — the bulletin states these procedures are for skilled technicians with proper tools and training, not do-it-yourselfers. If the 12V keeps dying or the MIL is on, book a Honda dealer and mention SB 25-043.
Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).
Typical time: “No parts; about 0.8 hour labor.” — as written in the note. First-timers often take twice this.
Honda service bulletin 25-043 (NHTSA doc MC-11019250-0001) applies to 2024–2025 Prologue, all trims. Symptom: the Malfunction Indicator Lamp may illuminate, or a 'Service High Voltage' message may appear, and the 12-volt battery may discharge intermittently or persistently.
The bulletin lists DTCs P2C8A, P2C8B, U3577, U3578, U3579, U357A, U357B, U357C, U357D, U357E, and U35AF. It states the procedure applies only when the full code set is present — a partial set sends the tech down a different diagnostic path.
Published cause: an internal Battery Energy Control Module (BECM) calibration anomaly setting battery-performance and communication DTCs. Published fix: update the BECM with the most recent software and perform the manual reset procedure twice. No parts; about 0.8 hour labor.
Owner-angle takeaway: a 12V battery that goes flat repeatedly soon after a jump or recharge is the tell. The 12V battery is the victim, not the cause — replacing it without the BECM software update just repeats the cycle.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
We don't have factory bulletin data for the 2024–2025 Honda Prologue yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.