Community-sourced DIY repair guides for the 2013–2017 Honda Accord, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Owner-verified repair guides
CVT judder / shudder Owner-verified(2.4L K24W I4)
Drain-and-fill is a driveway job: drain plug underneath, refill through the top fill hole, level set via the check bolt with the car level and the transmission at operating temperature. These CVTs have no dipstick.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Torque specs
CVT drain plug: 36 lb-ft — Per DIY community guides — verify against factory service info; do not overtighten the aluminum case.
CVT check bolt: 15 lb-ft — Per DIY community guides — verify against factory service info.
Tips
If the judder matches the TSB pattern (low-speed judder, especially cold), Honda's fix path is a TCM software update first, then valve body replacement per TSB 13-053 — multiple 2013 owners report the dealer valve-body job curing it. Check whether your VIN falls under the TSB before paying out of pocket.
For maintenance, do a drain-and-fill (about 3.7L out, the same amount back in) with Honda HCF-2 CVT fluid ONLY — the wrong fluid damages the transmission. The maintenance minder typically calls for it around the 50k-mile mark.
Level-check procedure: car level, transmission at operating temperature, cycle the shifter through all positions, then remove the 12mm check bolt — a slow drip means the level is correct. Fit a new crush washer (P/N 90471-PW7-A00) on the check bolt.
Never put these CVTs on a flush machine — Honda's procedure is drain-and-fill only, and owners report flushes causing new problems.
The starter comes out from below — about 10 minutes to remove per owner reports — and the rebuild itself is about 5 minutes on the bench.
Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).
Typical time: “The starter comes out from below — about 10 minutes to remove per owner reports — and the rebuild itself is about 5 minutes on the bench.” — as written in the note. First-timers often take twice this.
Torque specs
Starter mounting bolts: 33 lb-ft — Per DIY community guides — verify against factory service info.
Tips
Symptom pattern: occasional no-start on the first attempt that always catches on the second, progressing over weeks. That is the classic worn-brush failure on these Mitsuba starters — catch it early and it never strands you.
The $35 fix is the Honda brush holder kit (P/N 31210-5A2-A01) — you do not need a whole starter. A dealer will quote roughly $1,000 for complete starter replacement plus labor; the brushes are what actually fail.
If you'd rather not rebuild, a full starter swap is a straightforward DIY with 10/12/14mm sockets and roughly $100 in parts — but try the brush kit first and keep the thousand dollars.
Starter replacement is a driveway job; the TSB's flywheel rotation step adds work near the transmission.
Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).
Torque specs
Starter mounting bolts: 33 lb-ft — Per DIY community guides — verify against factory service info.
Tips
Honda TSB 16-002 covers the grinding pinion gear: inadequate clearance between the starter gear and the torque converter ring gear. Honda's prescribed fix is the redesigned starter (P/N 31200-5G0-A04) plus rotating the flywheel one bolt hole.
Honest caveat from the owner community: multiple owners — including a former Honda drivetrain engineer posting on DriveAccord — report the TSB fix being temporary, with grinding returning in 1–2 months even after dealer work. Go in with eyes open.
Community alternative with reported success: a previous-generation V6 starter (P/N 31200-R70-A51, Denso 280-0403) without the flywheel rotation — owners report this holding where the TSB fix didn't. Treat it as owner-reported, not Honda-endorsed.
The VTC actuator sits on the intake cam sprocket - the valve cover comes off to reach it. The rattle shows after a cold soak (roughly 6+ hours sitting); a warm engine will not reproduce it, so diagnose on the first start of the day.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Torque specs
VTC actuator / timing components: verify — Torque specs not confirmed from a forum source - confirm against factory service info before torquing.
Tips
Diagnosis first: a loud rattle lasting about 1 to 3 seconds on cold startup that then goes quiet is the VTC actuator's locking pin not holding, per Honda techline article ATS160717. If the rattle persists warm or sounds like slapping/clicking at idle instead, suspect the cam chain auto-tensioner (a separately documented 2013 Accord issue) - different fix.
Honda's documented fix is the VTC actuator itself, not the chain: one 9th-gen owner's dealer work order listed only the VTC actuator and Hondabond, and the rattle was gone after cold soaks. This matches the 2008-2012 note's lesson - same failure, different generation, different TSB.
Consider the timing chain, guides, and tensioner while you are in there at high mileage - a Honda tech notes K-series chains stretch over time and a skipped tooth causes valve damage. The actuator job overlaps that access, and $600-700 shop quotes for the actuator typically assume the related parts.
Fresh oil of the correct weight matters going forward: the actuator is hydraulically controlled, and neglected oil accelerates the wear that causes the rattle. Do not confuse this with the V6 timing-belt tensioner tick - the 2.4L uses a chain.
Dipstick and tailpipe tell the story for free: check the oil level cold, same flat spot, every fill-up for a few weeks. A quart every 1,000-2,000 miles on a 2013-2014 2.4L with no drips on the driveway is the TSB pattern.
Typical difficulty: Moderate — based on 5 code guides for the oil repair area (an area-level estimate, not this exact job).
Tips
This is a Honda-documented defect: TSB 17-089 (2013-2014 Accord L4, all trims except Hybrid) says engine oil consumption exceeding expectations is caused by oil control rings clogged with carbon deposits that can't scrape oil back to the crankcase. The dealer's fix is an oil consumption test, then new pistons, pins, rings, oil jets, and spark plugs.
The owner evidence is overwhelming for 2013-2014 cars: CarComplaints owners report a quart every 1,000 miles at 36,000-55,000 miles, dipsticks going dry between changes, and dealers calling it 'normal' before the TSB existed. No puddles under the car - the oil goes out the tailpipe, not onto the driveway.
Check your oil yourself before trusting a dealer's test: owners report dealers doing consumption tests slowly or declaring normal consumption on cars clearly burning oil. Track miles-per-quart over two full oil changes and walk in with numbers.
Prevention owners swear by: shorter oil-change intervals, quality full synthetic, and a fresh PCV valve - one owner cut consumption from 1 quart per 2,000 miles to half that with a high-detergent synthetic, suggesting the ring deposits respond to oil quality.
If you're out of any warranty coverage, the TSB's piston-and-ring job is engine-out expensive at a shop - which is why owners of older cars mostly just top up every 1,000 miles and watch the dipstick. A quart in 5,000 miles on a high-mileage K24 is not this problem; a quart in 1,000-2,000 on a low-mileage one is.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
What owners report
NHTSA recorded 607 complaints for the 2013–2017 Honda Accord. 2016 was the worst year (607 complaints). Most-reported areas: electrical system, exterior lighting, unknown or other.
17V418000 (29/06/2017) — ELECTRICAL SYSTEM:12V/24V/48V BATTERY Honda (American Honda Motor Co.) is recalling certain 2013-2016 Honda Accord vehicles. The case for the battery sensor, part of the battery management system, may allow water to get in, potentially causing an electrical short.
19V060000 (29/01/2019) — FUEL SYSTEM, OTHER:DELIVERY:FUEL PUMP Honda (American Honda Motor Co.) is recalling certain 2016-2018 Acura MDX, 2015-2019 Acura TLX and 2015-2017 Honda Accord vehicles, equipped with a 3.5L V6 engine. Particulates in fuel may adhere to the internal components of the fuel pump, reducing its…
4 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
We don't have factory bulletin data for the 2013–2017 Honda Accord yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.