Community-sourced DIY repair guides for the 2020–2026 Ford F-350, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Owner-verified repair guides
10R140 10-speed fluid + filter service — Mercon ULV only, and the 2023+ fill-plug change Owner-verified(all)
Driveway job — pan drop with hand tools; no flush machine needed. There is no under-hood dipstick: the level check is a short dipstick inside the side fill plug, read with the transmission fully hot. On 2023+ trucks Ford deleted the side fill plug, so the refill goes in from the top of the transmission.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Tips
Mercon ULV and nothing else — Motorcraft XT-12-QULV (WSS-M2C949-A). This is the single most-repeated owner warning: the 10R140 is ULV-only. The transfer case and power steering on the same truck take Mercon LV — keep the two bottles straight or you'll fill the wrong unit.
Fill quantities from the workshop manual as quoted by owners: 6 quarts is the starting point; add 2 more quarts when the pan and filter have been removed (8 quarts total for a pan-drop service). The filter is FT221 / Motorcraft LC3Z-7G186-A.
2023+ change you need to know: Ford deleted the side fill plug on the 2023+ 10R140 — the refill now goes in from the top of the transmission. If your video guide shows the side plug, you're watching a 2020-2022 procedure.
Level check is hot-only: pull the side fill plug (2020-2022) and read the short dipstick inside it with the transmission fully hot — owners recheck once trans temp is above 200°F. There is no under-hood dipstick on this truck, so don't go looking for one.
Pan drop vs dealer flush: owners report a pan drop replaces roughly half the fluid (the rest lives in the converter and cooler). A dealer low-pressure flush was quoted at $330 and replaces ~100% — dealers push the flush over the pan drop, but only the pan drop gets you a new filter. Many owners do pan + filter at 60k.
One owner's expensive lesson: after a DIY filter change the filter bushing dislodged and the pan gasket pinched near the engine, causing harsh engagement into Drive until reseated. Seat the filter fully and watch the gasket on the way back up.
Don't panic at the temps: these run hot by design. Owners coming from older trucks are alarmed the first time they see 200°F+, but that's normal operating range for the 10R140, not an overheat.
7.3L 16-plug service — the two-plugs-per-cylinder tax on your schedule Owner-verified(7.3L Godzilla V8)
Driveway job — all 16 plugs are reachable with the coil packs on the valve covers and short plug wires; no intake removal. Do it on a cold engine.
Typical difficulty: Easy — based on 64 code guides for the ignition repair area (an area-level estimate, not this exact job).
Torque specs
Spark plugs (16, two per cylinder): 133 lb-in (15 N·m) — Per the 2024 Super Duty shop manual as quoted by an owner; tighten on a cold engine. Motorcraft plugs are pre-coated — no anti-seize.
Tips
It's 16 plugs, two per cylinder — buy 16, not 8. The Godzilla kept Ford's two-plug-per-cylinder big-block tradition, so the parts bill and the labor are both double what the plug count suggests.
Torque spec is 133 lb-in (15 N·m) per the 2024 Super Duty shop manual, quoted by an owner — and that's inch-pounds, not foot-pounds. Tighten on a cold engine.
Stay with Motorcraft plugs and wires: that's the owner consensus ('I stayed with OEM and recommend the same'). The Godzilla's coils sit on the valve covers with short plug wires — inspect every wire while you're in there.
The book says 100k for plugs, but owners doing heavy towing are in there at 40-60k (one F-350 7.3 owner documented a full change at 40k). If your wires are original 2020-2021 units, change them with the plugs — heat damage near the exhaust manifolds was the TSB 20-2370 misfire campaign, and worn wires make new plugs pointless.
This is scheduled maintenance, not the TSB: TSB 20-2370 covered defective 2020-2021 plug wires causing misfire under load. A plug service applies to every Godzilla on the calendar, misfire or not.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
We don't have factory bulletin data for the 2020–2026 Ford F-350 yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.