Community-sourced DIY repair guides for the 2020–2021 Ford F-350, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Owner-verified repair guides
7.3L Godzilla misfire under load from heat-damaged spark plug wires — TSB 20-2370 Factory-documented(7.3L Godzilla V8)
A plug-wire swap on the 7.3L is a 20-minute, no-tools driveway job on a COLD engine. Carry a spare wire (or set) in the truck — they are about $18-30 each and dealers were chronically out of stock.
Typical difficulty: Easy — based on 64 code guides for the ignition repair area (an area-level estimate, not this exact job).
Torque specs
Spark plug wires: n/a — Press-fit boots — no torque spec; route the revised wires per the TSB and keep them clear of the exhaust manifolds.
Tips
TSB 20-2370: 2020-2021 F-Super Duty trucks with the 7.3L Godzilla built on or before September 28, 2020 can set P0300, P0316, or P0301-P0304 with an illuminated (often flashing) MIL, misfire, or lack of power. Root cause is the early plug wires' poor heat insulation — the Godzilla runs very hot, especially under load.
The classic owner story, confirmed by multiple F-350 7.3L owners: engine runs fine unloaded, then misfires hard on a grade or while towing — flashing CEL, sometimes limp mode and the A/C cutting out. Let it cool and it behaves again until the next hard pull.
Fix is the revised plug-wire set per the TSB (make sure the dealer orders the TSB part number — owners report parts counters trying to sell the old-design wire). The swap is genuinely a 20-minute, no-tools job on a cold engine, roughly $18-30 per wire.
Carry spares: owners who tow remote recommend keeping a wire or two under the back seat, since dealers were frequently out of stock and some trucks sat for days waiting on parts.
Don't confuse this with the rarer 7.3L lifter/cam failure: if new wires, plugs, and coils don't fix a persistent misfire on one cylinder, escalate to a dealer diagnosis rather than throwing more ignition parts at it.
Recall inspection is dealer-only. There is no owner repair — and no warning before a failure, so do not defer the inspection.
Typical difficulty: Moderate — based on 60 code guides for the steering repair area (an area-level estimate, not this exact job).
Torque specs
Recall remedy: verify — Dealer inspects and repairs or replaces the steering column upper shaft, free of charge — no DIY torque involved.
Tips
NHTSA 25V626 (filed September 2025): certain 2020-2021 F-250, F-350, and F-450 Super Duty trucks built February 2019 through September 2020 — 115,539 trucks — can lose steering if the steering column's upper shaft separates from the lower shaft.
Root cause: a supplier (HL Mando) upper shaft that doesn't meet anti-pull-apart load specs; trucks built before February 2021 used a single 'staking' retention process, with a second staking added later. There is no dashboard warning and no steering feel change before separation — Ford estimates 1% of the recalled trucks have the defect.
Remedy: dealers inspect the column and repair or replace the upper steering shaft as required, free of charge. Trucks that pass inspection still get modified to improve pull-apart retention.
Ford had 17 potentially related reports and no known accidents or injuries at filing — but a steering-loss defect with zero warning is not one to sit on. Check the VIN and book the inspection.
This is a different issue from the 2025 column-shifter recall (25S20) already documented for the F-350 — a truck can be affected by both; check both campaigns by VIN.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
We don't have factory bulletin data for the 2020–2021 Ford F-350 yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.