Community-sourced DIY repair guides for the 2017–2019 Ford F-350, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Owner-verified repair guides
Engine block heater cord fire risk — recall saga (18V894 → 19V278) Factory-documented(6.2L Boss V8, 6.7L Power Stroke V8 diesel)
Free at the dealer under 18S45/19S11. Check your VIN at nhtsa.gov/recalls or call Ford at 1-866-436-7332. If you have a block heater, look at the cord for melted insulation or a corroded splice connector before plugging it in again.
Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).
Torque specs
Recall remedy: verify — Dealer disables the block heater cord under 19S11 and replaces the cord assembly when parts are available — no DIY torque involved. Verify your truck's recall completion by VIN.
Tips
If your F-350 has an engine block heater, this is a fire-risk recall you want to confirm was actually completed. In December 2018 Ford recalled 410,289 trucks (NHTSA 18V894, Ford 18S45): water and contaminants could get into the block heater cable's splice connector, corrode it, and cause a resistive short — overheated or melted wiring.
Then it got a rerecall. In April 2019 Ford issued 19V278 (Ford 19S11) covering 131,068 trucks because the splice connector may have been damaged during the first recall's repair. The interim fix was brutal: dealers disabled the block heater entirely with a 'DO NOT USE — RISK OF FIRE' notice until replacement cords existed.
The permanent fix is a replacement block heater cord, free at the dealer. If you bought your truck used, don't assume a previous owner handled this — check your VIN at nhtsa.gov/recalls, because the second recall only covers trucks already remedied under the first.
Cold-climate trucks are the ones at risk here, since that's where block heaters get used. If you plug yours in, give the cord and the splice connector a look first: cracked insulation, green corrosion, or anything that smells hot means don't use it until the dealer checks it.
Note the scope: 2017-2019 Super Duty trucks (F-250 through F-550) with the factory block heater. F-150s with block heaters were in the same recalls, so if you also own an F-150, check it too.
TSB work is done at the dealer, but the damper itself is a bolt-on part a DIYer can swap in a driveway in about 30 minutes (two bolts) once diagnosed.
Typical difficulty: Moderate — based on 60 code guides for the steering repair area (an area-level estimate, not this exact job).
Typical time: “TSB work is done at the dealer, but the damper itself is a bolt-on part a DIYer can swap in a driveway in about 30 minutes (two bolts) once diagnosed.” — as written in the note. First-timers often take twice this.
Torque specs
Steering damper bolts: verify — Bolt-on part — confirm torque in the service manual; forum owners report a ~30-minute driveway swap.
Tips
TSB 18-2268 (superseded by 19-2274) covers 2017-2019 F-250/F-350 4WD trucks built on or before July 31, 2018: sustained steering-wheel oscillation after hitting rough pavement or an expansion joint above 45 mph. 2WD F-350s are not in the TSB population.
Ford's prescribed fix: inspect the steering linkage damper and replace it with the revised damper (HC3Z-3E651-D, then HC3Z-3E651-F under 19-2274), plus caster correction via upper ball-joint sleeve adjusters if the damper alone doesn't cure it. Eligible under the New Vehicle Limited Warranty.
F-350 owners on the forums confirm the fix works when done right, but some report the wobble returning — in which case the checklist is: tire pressure and balance, track-bar bushings and ball joints, caster at the low end of spec, then the damper.
Out of warranty, a DIY damper swap is one of the cheapest Super Duty jobs: a quality aftermarket stabilizer (Bilstein 5100 and similar are forum favorites) and basic hand tools, roughly 30 minutes under the front end. Dealer damper labor under the TSB books at 0.4 hour.
Context: Ford faced a class-action over Super Duty death wobble (2005-2007 and 2017-2019 F-250/F-350 trucks cited), with ~1,265 complaints mentioned in the suit — so document every occurrence with the dealer in writing.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
We don't have factory bulletin data for the 2017–2019 Ford F-350 yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.